.. _power_management_api: Power Management ################ Zephyr RTOS power management subsystem provides several means for a system integrator to implement power management support that can take full advantage of the power saving features of SOCs. Terminology *********** :dfn:`SOC interface` This is a general term for the components that have knowledge of the SOC and provide interfaces to the hardware features. It will abstract the SOC specific implementations to the applications and the OS. :dfn:`Idle Thread` A system thread that runs when there are no other threads ready to run. :dfn:`Power gating` Power gating reduces power consumption by shutting off current to blocks of the integrated circuit that are not in use. :dfn:`Power State` SOC Power State describes processor and device power states implemented at the SOC level. Power states are represented by :c:enum:`pm_state` and each one has a different meaning. Overview ******** The interfaces and APIs provided by the power management subsystem are designed to be architecture and SOC independent. This enables power management implementations to be easily adapted to different SOCs and architectures. The architecture and SOC independence is achieved by separating the core infrastructure and the SOC specific implementations. The SOC specific implementations are abstracted to the application and the OS using hardware abstraction layers. The power management features are classified into the following categories. * Tickless Idle * System Power Management * Device Power Management Tickless Idle ************* This is the name used to identify the event-based idling mechanism of the Zephyr RTOS kernel scheduler. The kernel scheduler can run in two modes. During normal operation, when at least one thread is active, it sets up the system timer in periodic mode and runs in an interval-based scheduling mode. The interval-based mode allows it to time slice between threads. Many times, the threads would be waiting on semaphores, timeouts or for events. When there are no threads running, it is inefficient for the kernel scheduler to run in interval-based mode. This is because, in this mode the timer would trigger an interrupt at fixed intervals causing the scheduler to be invoked at each interval. The scheduler checks if any thread is ready to run. If no thread is ready to run then it is a waste of power because of the unnecessary CPU processing. This is avoided by the kernel switching to event-based idling mode whenever there is no thread ready to run. The kernel holds an ordered list of thread timeouts in the system. These are the amount of time each thread has requested to wait. When the last active thread goes to wait, the idle thread is scheduled. The idle thread programs the timer to one-shot mode and programs the count to the earliest timeout from the ordered thread timeout list. When the timer expires, a timer event is generated. The ISR of this event will invoke the scheduler, which would schedule the thread associated with the timeout. Before scheduling the thread, the scheduler would switch the timer again to periodic mode. This method saves power because the CPU is removed from the wait only when there is a thread ready to run or if an external event occurred. System Power Management *********************** The kernel enters the idle state when it has nothing to schedule. If enabled via the :option:`CONFIG_PM` Kconfig option, the Power Management Subsystem can put an idle system in one of the supported power states, based on the selected power management policy and the duration of the idle time allotted by the kernel. It is an application responsibility to set up a wake up event. A wake up event will typically be an interrupt triggered by one of the SoC peripheral modules such as a SysTick, RTC, counter, or GPIO. Depending on the power mode entered, only some SoC peripheral modules may be active and can be used as a wake up source. Enabling system power management compels the Zephyr kernel scheduler to work in tickless idle mode (see :option:`CONFIG_TICKLESS_IDLE`). Power States ============ The power management subsystem contains a set of states based on power consumption and context retention. The list of available power states is defined by :c:enum:`pm_state`. In general power states with higher indexes will offer greater power savings and have higher wake latencies. Following is a thorough list of available states: .. doxygenenumvalue:: PM_STATE_ACTIVE :project: Zephyr .. doxygenenumvalue:: PM_STATE_RUNTIME_IDLE :project: Zephyr .. doxygenenumvalue:: PM_STATE_SUSPEND_TO_IDLE :project: Zephyr .. doxygenenumvalue:: PM_STATE_STANDBY :project: Zephyr .. doxygenenumvalue:: PM_STATE_SUSPEND_TO_RAM :project: Zephyr .. doxygenenumvalue:: PM_STATE_SUSPEND_TO_DISK :project: Zephyr .. doxygenenumvalue:: PM_STATE_SOFT_OFF :project: Zephyr Power Management Policies ========================= The power management subsystem supports the following power management policies: * Residency * Application * Dummy Residency --------- The power management system enters the power state which offers the highest power savings, and with a minimum residency value (defined by the respective Kconfig option) less than or equal to the scheduled system idle time duration. Application ----------- The power management policy is defined by the application which has to implement the following function. .. code-block:: c struct pm_state_info pm_policy_next_state(int32_t ticks); Dummy ----- This policy returns the next supported power state in a loop. It is used mainly for testing purposes. Device Power Management Infrastructure ************************************** The device power management infrastructure consists of interfaces to the Zephyr RTOS device model. These APIs send control commands to the device driver to update its power state or to get its current power state. Zephyr RTOS supports two methods of doing device power management. * Distributed method * Central method Distributed method ================== In this method, the application or any component that deals with devices directly and has the best knowledge of their use does the device power management. This saves power if some devices that are not in use can be turned off or put in power saving mode. This method allows saving power even when the CPU is active. The components that use the devices need to be power aware and should be able to make decisions related to managing device power. In this method, the SOC interface can enter CPU or SOC power states quickly when :code:`sys_suspend()` gets called. This is because it does not need to spend time doing device power management if the devices are already put in the appropriate power state by the application or component managing the devices. Central method ============== In this method device power management is mostly done inside :code:`sys_suspend()` along with entering a CPU or SOC power state. If a decision to enter deep sleep is made, the implementation would enter it only after checking if the devices are not in the middle of a hardware transaction that cannot be interrupted. This method can be used in implementations where the applications and components using devices are not expected to be power aware and do not implement device power management. .. image:: central_method.svg :align: center This method can also be used to emulate a hardware feature supported by some SOCs which cause automatic entry to deep sleep when all devices are idle. Refer to `Busy Status Indication`_ to see how to indicate whether a device is busy or idle. Device Power Management States ============================== The Zephyr RTOS power management subsystem defines four device states. These states are classified based on the degree of device context that gets lost in those states, kind of operations done to save power, and the impact on the device behavior due to the state transition. Device context includes device registers, clocks, memory etc. The four device power states: :code:`DEVICE_PM_ACTIVE_STATE` Normal operation of the device. All device context is retained. :code:`DEVICE_PM_LOW_POWER_STATE` Device context is preserved by the HW and need not be restored by the driver. :code:`DEVICE_PM_SUSPEND_STATE` Most device context is lost by the hardware. Device drivers must save and restore or reinitialize any context lost by the hardware. :code:`DEVICE_PM_OFF_STATE` Power has been fully removed from the device. The device context is lost when this state is entered. Need to reinitialize the device when powering it back on. Device Power Management Operations ================================== Zephyr RTOS power management subsystem provides a control function interface to device drivers to indicate power management operations to perform. The supported PM control commands are: * DEVICE_PM_SET_POWER_STATE * DEVICE_PM_GET_POWER_STATE Each device driver defines: * The device's supported power states. * The device's supported transitions between power states. * The device's necessary operations to handle the transition between power states. The following are some examples of operations that the device driver may perform in transition between power states: * Save/Restore device states. * Gate/Un-gate clocks. * Gate/Un-gate power. * Mask/Un-mask interrupts. Device Model with Power Management Support ========================================== Drivers initialize the devices using macros. See :ref:`device_model_api` for details on how these macros are used. Use the DEVICE_DEFINE macro to initialize drivers providing power management support via the PM control function. One of the macro parameters is the pointer to the device_pm_control handler function. Default Initializer Function ---------------------------- .. code-block:: c int device_pm_control_nop(const struct device *unused_device, uint32_t unused_ctrl_command, void *unused_context); If the driver doesn't implement any power control operations, the driver can initialize the corresponding pointer with this default nop function. This default nop function does nothing and should be used instead of implementing a dummy function to avoid wasting code memory in the driver. Device Power Management API =========================== The SOC interface and application use these APIs to perform power management operations on the devices. Get Device List --------------- .. code-block:: c size_t z_device_get_all_static(struct device const **device_list); The Zephyr RTOS kernel internally maintains a list of all devices in the system. The SOC interface uses this API to get the device list. The SOC interface can use the list to identify the devices on which to execute power management operations. .. note:: Ensure that the SOC interface does not alter the original list. Since the kernel uses the original list, it must remain unchanged. Device Set Power State ---------------------- .. code-block:: c int device_set_power_state(const struct device *device, uint32_t device_power_state, device_pm_cb cb, void *arg); Calls the :c:func:`device_pm_control()` handler function implemented by the device driver with DEVICE_PM_SET_POWER_STATE command. Device Get Power State ---------------------- .. code-block:: c int device_get_power_state(const struct device *device, uint32_t * device_power_state); Calls the :c:func:`device_pm_control()` handler function implemented by the device driver with DEVICE_PM_GET_POWER_STATE command. Busy Status Indication ====================== The SOC interface executes some power policies that can turn off power to devices, causing them to lose their state. If the devices are in the middle of some hardware transaction, like writing to flash memory when the power is turned off, then such transactions would be left in an inconsistent state. This infrastructure guards such transactions by indicating to the SOC interface that the device is in the middle of a hardware transaction. When the :code:`sys_suspend()` is called, the SOC interface checks if any device is busy. The SOC interface can then decide to execute a power management scheme other than deep sleep or to defer power management operations until the next call of :code:`sys_suspend()`. An alternative to using the busy status mechanism is to use the `distributed method`_ of device power management. In such a method where the device power management is handled in a distributed manner rather than centrally in :code:`sys_suspend()`, the decision to enter deep sleep can be made based on whether all devices are already turned off. This feature can be also used to emulate a hardware feature found in some SOCs that causes the system to automatically enter deep sleep when all devices are idle. In such an usage, the busy status can be set by default and cleared as each device becomes idle. When :code:`sys_suspend()` is called, deep sleep can be entered if no device is found to be busy. Here are the APIs used to set, clear, and check the busy status of devices. Indicate Busy Status API ------------------------ .. code-block:: c void device_busy_set(const struct device *busy_dev); Sets a bit corresponding to the device, in a data structure maintained by the kernel, to indicate whether or not it is in the middle of a transaction. Clear Busy Status API --------------------- .. code-block:: c void device_busy_clear(const struct device *busy_dev); Clears the bit corresponding to the device in a data structure maintained by the kernel to indicate that the device is not in the middle of a transaction. Check Busy Status of Single Device API -------------------------------------- .. code-block:: c int device_busy_check(const struct device *chk_dev); Checks whether a device is busy. The API returns 0 if the device is not busy. Check Busy Status of All Devices API ------------------------------------ .. code-block:: c int device_any_busy_check(void); Checks if any device is busy. The API returns 0 if no device in the system is busy. Device Idle Power Management **************************** The Device Idle Power Management framework is a Active Power Management mechanism which reduces the overall system Power consumtion by suspending the devices which are idle or not being used while the System is active or running. The framework uses device_set_power_state() API set the device power state accordingly based on the usage count. The interfaces and APIs provided by the Device Idle PM are designed to be generic and architecture independent. Device Idle Power Management API ================================ The Device Drivers use these APIs to perform device idle power management operations on the devices. Enable Device Idle Power Management of a Device API --------------------------------------------------- .. code-block:: c void device_pm_enable(const struct device *dev); Enbles Idle Power Management of the device. Disable Device Idle Power Management of a Device API ---------------------------------------------------- .. code-block:: c void device_pm_disable(const struct device *dev); Disables Idle Power Management of the device. Resume Device asynchronously API -------------------------------- .. code-block:: c int device_pm_get(const struct device *dev); Marks the device as being used. This API will asynchronously bring the device to resume state. The API returns 0 on success. Resume Device synchronously API ------------------------------- .. code-block:: c int device_pm_get_sync(const struct device *dev); Marks the device as being used. It will bring up or resume the device if it is in suspended state based on the device usage count. This call is blocked until the device PM state is changed to active. The API returns 0 on success. Suspend Device asynchronously API --------------------------------- .. code-block:: c int device_pm_put(const struct device *dev); Marks the device as being released. This API asynchronously put the device to suspend state if not already in suspend state. The API returns 0 on success. Suspend Device synchronously API -------------------------------- .. code-block:: c int device_pm_put_sync(const struct device *dev); Marks the device as being released. It will put the device to suspended state if is is in active state based on the device usage count. This call is blocked until the device PM state is changed to resume. The API returns 0 on success. This call is blocked until the device is suspended. Power Management Configuration Flags ************************************ The Power Management features can be individually enabled and disabled using the following configuration flags. :option:`CONFIG_PM` This flag enables the power management subsystem. :option:`CONFIG_TICKLESS_IDLE` This flag enables the tickless idle power saving feature. :option:`CONFIG_PM_DEVICE` This flag is enabled if the SOC interface and the devices support device power management. :code:`CONFIG_PM_DEVICE_IDLE` This flag enables the Device Idle Power Management. API Reference ************* Power Management Hook Interface =============================== .. doxygengroup:: power_management_hook_interface :project: Zephyr System Power Management APIs ============================ .. doxygengroup:: system_power_management_api :project: Zephyr Device Power Management APIs ============================ .. doxygengroup:: device_power_management_api :project: Zephyr