:orphan:

.. _nordic_nrf_qspi:

nordic,nrf-qspi
###############

Vendor: :ref:`Nordic Semiconductor <dt_vendor_nordic>`

Description
***********

These nodes are "qspi" bus nodes.

.. code-block:: none

   Properties defining the interface for the Nordic QSPI peripheral.

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``sck-pin``
           - ``int``
           - .. code-block:: none

                The SCK pin to use.

                For pins P0.0 through P0.31, use the pin number. For example,
                to use P0.16 for SCK, set:

                    sck-pin = <16>;

                For pins P1.0 through P1.31, add 32 to the pin number. For
                example, to use P1.2 for SCK, set:

                    sck-pin = <34>;  /* 32 + 2 */



             This property is **required**.

         * - ``io-pins``
           - ``array``
           - .. code-block:: none

                Pin numbers associated with IO0 through IO3 signals.

                Examples:

                    io-pins = <io0-pin io1-pin>; // two pins

                    io-pins = <io0-pin io1-pin io2-pin io3-pin>; // four pins

                Either two or four pins must be configured using this property
                as shown above. The pin numbering scheme is the same as the
                sck-pin property's.



             This property is **required**.

         * - ``csn-pins``
           - ``array``
           - .. code-block:: none

                Chip select signal pin number. Exactly one pin should be
                given. The pin numbering scheme is the same as the
                sck-pin property's.



             This property is **required**.



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nordic,nrf-qspi" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


             This property is **required**.

             Constant value: ``1``

         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


             This property is **required**.

         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers