:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: st,stm32f0-pll-clock
.. _dtbinding_st_stm32f0_pll_clock:

st,stm32f0-pll-clock
####################

Vendor: :ref:`STMicroelectronics <dt_vendor_st>`

Description
***********



.. code-block:: none

   Main PLL node binding for STM32F0 and STM32F3 devices.

   Takes one of clk_hse or clk_hsi as input clock.

   Note: Some STM32F0 SoC variants (STM32072 for instance) may also support HSI48
   as input clock. This case is not supported yet.

   Frequency calculation for output clock is as follows:

     f(PLLCLK) = f(PLLIN) x PLLMUL   --> SYSCLK (System Clock)

     with, depending on the case:
             If input_clk = clk_hse
               f(PLLIN) = f(input_clk) / PREDIV
             If input_clk = clk_hsi
               On STM32F3, STM32F03x, STM32F05x, STM32F030x4, STM32F030x6 and STM32F030x8
                 f(PLLIN) = f(input_clk) / 2
               On STM32F04x, STM32F07x, STM32F09x, STM32F070x6, STM32F070xB and STM32F030xC
                 f(PLLIN) = f(input_clk) / PREDIV

   The PLL output frequency must be set in range 16-48MHz

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``mul``
           - ``int``
           - .. code-block:: none

                PLL multiplication factor for output clock
                Valid range: 2 - 16



             This property is **required**.

         * - ``#clock-cells``
           - ``int``
           - .. code-block:: none

                Number of items to expect in a Clock specifier


             This property is **required**.

         * - ``prediv``
           - ``int``
           - .. code-block:: none

                Configurable prescaler
                Valid range: 1 - 16





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "st,stm32f0-pll-clock" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


             This property is **required**.

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers