:orphan:
.. raw:: html
.. dtcompatible:: nxp,fxos8700
.. _dtbinding_nxp_fxos8700:
nxp,fxos8700 (on i2c bus)
#########################
Vendor: :ref:`NXP Semiconductors `
Description
***********
.. code-block:: none
FXOS8700 6-axis accelerometer/magnetometer sensor
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reset-gpios``
- ``phandle-array``
- .. code-block:: none
RST pin This pin defaults to active high when consumed by the sensor. The property value should ensure the flags properly describe the signal that is presented to the driver.
* - ``int1-gpios``
- ``phandle-array``
- .. code-block:: none
INT1 pin This pin defaults to active low when produced by the sensor. The property value should ensure the flags properly describe the signal that is presented to the driver.
* - ``int2-gpios``
- ``phandle-array``
- .. code-block:: none
INT2 pin This pin defaults to active low when produced by the sensor. The property value should ensure the flags properly describe the signal that is presented to the driver.
* - ``range``
- ``int``
- .. code-block:: none
Range in g
Default value: ``8``
Legal values: ``8``, ``4``, ``2``
* - ``power-mode``
- ``int``
- .. code-block:: none
Power mode
Legal values: ``0``, ``1``, ``2``, ``3``
* - ``pulse-cfg``
- ``int``
- .. code-block:: none
Pulse configuration register
Default value: ``63``
* - ``pulse-thsx``
- ``int``
- .. code-block:: none
Pulse X-axis threshold Threshold to start the pulse-event detection procedure on the X-axis. Threshold values for each axis are unsigned 7-bit numbers with a fixed resolution of 0.063 g/LSB, corresponding to an 8g acceleration full-scale range.
Default value: ``32``
* - ``pulse-thsy``
- ``int``
- .. code-block:: none
Pulse Y-axis threshold Threshold to start the pulse-event detection procedure on the Y-axis. Threshold values for each axis are unsigned 7-bit numbers with a fixed resolution of 0.063 g/LSB, corresponding to an 8g acceleration full-scale range.
Default value: ``32``
* - ``pulse-thsz``
- ``int``
- .. code-block:: none
Pulse Z-axis threshold Threshold to start the pulse-event detection procedure on the Z-axis. Threshold values for each axis are unsigned 7-bit numbers with a fixed resolution of 0.063 g/LSB, corresponding to an 8g acceleration full-scale range.
Default value: ``64``
* - ``pulse-tmlt``
- ``int``
- .. code-block:: none
Pulse time limit The maximum time interval that can elapse between the start of the acceleration on the selected channel exceeding the specified threshold and the end when the channel acceleration goes back below the specified threshold. The resolution depends upon the sample rate (ODR) and the high-pass filter configuration (HP_FILTER_CUTOFF[pls_hpf_en]). For ODR=800 Hz and pls_hpf_en=0, the resolution is 0.625 ms/LSB.
Default value: ``24``
* - ``pulse-ltcy``
- ``int``
- .. code-block:: none
Pulse latency The time interval that starts after the first pulse detection where the pulse-detection function ignores the start of a new pulse. The resolution depends upon the sample rate (ODR) and the high-pass filter configuration (HP_FILTER_CUTOFF[pls_hpf_en]). For ODR=800 Hz and pls_hpf_en=0, the resolution is 1.25 ms/LSB.
Default value: ``40``
* - ``pulse-wind``
- ``int``
- .. code-block:: none
Pulse window The maximum interval of time that can elapse after the end of the latency interval in which the start of the second pulse event must be detected provided the device has been configured for double pulse detection. The detected second pulse width must be shorter than the time limit constraint specified by the PULSE_TMLT register, but the end of the double pulse need not finish within the time specified by the PULSE_WIND register. The resolution depends upon the sample rate (ODR) and the high-pass filter configuration (HP_FILTER_CUTOFF[pls_hpf_en]). For ODR=800 Hz and pls_hpf_en=0, the resolution is 1.25 ms/LSB.
Default value: ``60``
* - ``mag-vecm-cfg``
- ``int``
- .. code-block:: none
Magnetic vector-magnitude configuration register
Default value: ``78``
* - ``mag-vecm-ths-msb``
- ``int``
- .. code-block:: none
Magnetic vector-magnitude threshold most significant byte. Resolution is 0.1 uT/LSB.
* - ``mag-vecm-ths-lsb``
- ``int``
- .. code-block:: none
Magnetic vector-magnitude threshold least significant byte. Resolution is 0.1 uT/LSB.
Default value: ``90``
* - ``supply-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
* - ``vin-supply``
- ``phandle``
- .. code-block:: none
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "nxp,fxos8700" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
device address on i2c bus
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers