:orphan:

.. title:: UART_IMX

.. option:: CONFIG_UART_IMX

*NXP i.MX7 family processor UART driver*

Type: ``bool``

Help
====

.. code-block:: none

    This option enables the UART driver for NXP i.MX7
    family processors.

Direct dependencies
===================

(\ :option:`SERIAL <CONFIG_SERIAL>` && \ :option:`SOC_MCIMX6X_M4 <CONFIG_SOC_MCIMX6X_M4>` && \ :option:`SOC_SERIES_IMX_6X_M4 <CONFIG_SOC_SERIES_IMX_6X_M4>`) || (\ :option:`SERIAL <CONFIG_SERIAL>` && \ :option:`SOC_MCIMX7_M4 <CONFIG_SOC_MCIMX7_M4>` && \ :option:`SOC_SERIES_IMX7_M4 <CONFIG_SOC_SERIES_IMX7_M4>`) || (\ :option:`HAS_IMX_HAL <CONFIG_HAS_IMX_HAL>` && \ :option:`SERIAL <CONFIG_SERIAL>`)

*(Includes any dependencies from ifs and menus.)*

Defaults
========

- y
- y

Symbols selected by this symbol
===============================

- \ :option:`SERIAL_HAS_DRIVER <CONFIG_SERIAL_HAS_DRIVER>`
- \ :option:`SERIAL_SUPPORT_INTERRUPT <CONFIG_SERIAL_SUPPORT_INTERRUPT>`

Kconfig definitions
===================



At ``<Zephyr SoC>/arm/nxp_imx/mcimx6x_m4/Kconfig.defconfig.mcimx6x_m4:18``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:19`` → ``<BuildDir>/kconfig/Kconfig.soc.defconfig:1`` → ``<Zephyr SoC>/arm/nxp_imx/Kconfig.defconfig:4`` → ``<Zephyr SoC>/arm/nxp_imx/mcimx6x_m4/Kconfig.defconfig.series:15``

Menu path: (Top)

.. code-block:: kconfig

    config UART_IMX
    	bool
    	default y
    	depends on SERIAL && SOC_MCIMX6X_M4 && SOC_SERIES_IMX_6X_M4

----

At ``<Zephyr SoC>/arm/nxp_imx/mcimx7_m4/Kconfig.defconfig.mcimx7_m4:21``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:19`` → ``<BuildDir>/kconfig/Kconfig.soc.defconfig:1`` → ``<Zephyr SoC>/arm/nxp_imx/Kconfig.defconfig:4`` → ``<Zephyr SoC>/arm/nxp_imx/mcimx7_m4/Kconfig.defconfig.series:15``

Menu path: (Top)

.. code-block:: kconfig

    config UART_IMX
    	bool
    	default y
    	depends on SERIAL && SOC_MCIMX7_M4 && SOC_SERIES_IMX7_M4

----

At ``<Zephyr Driver>/serial/Kconfig.imx:6``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:32`` → ``<Zephyr Driver>/Kconfig:24`` → ``<Zephyr Driver>/serial/Kconfig:81``

Menu path: (Top) → Device Drivers → Serial Drivers

.. code-block:: kconfig

    config UART_IMX
    	bool "NXP i.MX7 family processor UART driver"
    	select SERIAL_HAS_DRIVER
    	select SERIAL_SUPPORT_INTERRUPT
    	depends on HAS_IMX_HAL && SERIAL
    	help
    	  This option enables the UART driver for NXP i.MX7
    	  family processors.

*(The 'depends on' condition includes propagated dependencies from ifs and menus.)*