:orphan:

.. title:: CONFIG_I2S_STM32_USE_PLLI2S_ENABLE

.. kconfig:: CONFIG_I2S_STM32_USE_PLLI2S_ENABLE

CONFIG_I2S_STM32_USE_PLLI2S_ENABLE
##################################

*Enable usage of PLL*

Type: ``bool``

Help
====

.. code-block:: none

    Enable it if I2S clock should be provided by the PLLI2S.
    If not enabled the clock will be provided by HSI/HSE.

Direct dependencies
===================

(\ :kconfig:`I2S <CONFIG_I2S>` && \ :kconfig:`BOARD_NUCLEO_F411RE <CONFIG_BOARD_NUCLEO_F411RE>`) || (\ :kconfig:`I2S <CONFIG_I2S>` && \ :kconfig:`BOARD_NUCLEO_F411RE <CONFIG_BOARD_NUCLEO_F411RE>`) || (\ :kconfig:`I2S <CONFIG_I2S>` && \ :kconfig:`BOARD_96B_ARGONKEY <CONFIG_BOARD_96B_ARGONKEY>`) || (\ :kconfig:`I2S <CONFIG_I2S>` && \ :kconfig:`BOARD_96B_STM32_SENSOR_MEZ <CONFIG_BOARD_96B_STM32_SENSOR_MEZ>`) || (\ :kconfig:`I2S <CONFIG_I2S>` && \ :kconfig:`BOARD_NUCLEO_F411RE <CONFIG_BOARD_NUCLEO_F411RE>`) || (\ :kconfig:`I2S_STM32 <CONFIG_I2S_STM32>` && \ :kconfig:`I2S <CONFIG_I2S>`)

*(Includes any dependencies from ifs and menus.)*

Defaults
========

- y
- y
- y
- y
- y

Kconfig definitions
===================



At ``<Zephyr Boards>/shields/x_nucleo_iks02a1/boards/nucleo_f411re.defconfig:31``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:18`` → ``<BuildDir>/kconfig/Kconfig.shield.defconfig:1`` → ``<Zephyr Boards>/shields/x_nucleo_iks02a1/Kconfig.defconfig:5``

Menu path: (Top)

.. code-block:: kconfig

    config I2S_STM32_USE_PLLI2S_ENABLE
    	bool
    	default y
    	depends on I2S && BOARD_NUCLEO_F411RE

----

At ``<Zephyr Boards>/shields/x_nucleo_iks02a1/boards/nucleo_f411re.defconfig:31``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:20`` → ``<Zephyr Boards>/shields/x_nucleo_iks02a1/Kconfig.defconfig:5``

Menu path: (Top)

.. code-block:: kconfig

    config I2S_STM32_USE_PLLI2S_ENABLE
    	bool
    	default y
    	depends on I2S && BOARD_NUCLEO_F411RE

----

At ``<Zephyr Boards>/arm/96b_argonkey/Kconfig.defconfig:14``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:22``

Menu path: (Top)

.. code-block:: kconfig

    config I2S_STM32_USE_PLLI2S_ENABLE
    	bool
    	default y
    	depends on I2S && BOARD_96B_ARGONKEY

----

At ``<Zephyr Boards>/arm/96b_stm32_sensor_mez/Kconfig.defconfig:14``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:22``

Menu path: (Top)

.. code-block:: kconfig

    config I2S_STM32_USE_PLLI2S_ENABLE
    	bool
    	default y
    	depends on I2S && BOARD_96B_STM32_SENSOR_MEZ

----

At ``<Zephyr Boards>/shields/x_nucleo_iks02a1/boards/nucleo_f411re.defconfig:31``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:22`` → ``<Zephyr Boards>/shields/x_nucleo_iks02a1/Kconfig.defconfig:5``

Menu path: (Top)

.. code-block:: kconfig

    config I2S_STM32_USE_PLLI2S_ENABLE
    	bool
    	default y
    	depends on I2S && BOARD_NUCLEO_F411RE

----

At ``<Zephyr Driver>/i2s/Kconfig.stm32:24``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:42`` → ``<Zephyr Driver>/Kconfig:44`` → ``<Zephyr Driver>/i2s/Kconfig:28``

Menu path: (Top) → Device Drivers → I2S bus drivers → STM32 MCU I2S controller driver

.. code-block:: kconfig

    config I2S_STM32_USE_PLLI2S_ENABLE
    	bool "Enable usage of PLL"
    	depends on I2S_STM32 && I2S
    	help
    	  Enable it if I2S clock should be provided by the PLLI2S.
    	  If not enabled the clock will be provided by HSI/HSE.

*(The 'depends on' condition includes propagated dependencies from ifs and menus.)*