:orphan:
.. raw:: html
.. dtcompatible:: atmel,sam0-gmac
.. _dtbinding_atmel_sam0_gmac:
atmel,sam0-gmac
###############
Vendor: :ref:`Atmel Corporation `
Description
***********
.. code-block:: none
Atmel SAM0-family GMAC Ethernet
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``num-queues``
- ``int``
- .. code-block:: none
Number of hardware TX and RX queues.
This property is **required**.
* - ``max-frame-size``
- ``int``
- .. code-block:: none
Maximum ethernet frame size. The current ethernet frame sizes
supported by hardware are 1518, 1536 and 10240 (jumbo frames). This
means that normally gmac will reject any frame above max-frame-size
value. The default value is 1518, which represents an usual
IEEE 802.3 ethernet frame:
Ethernet Frame [ 14 MAC HEADER | 1500 MTU | 4 FCS ] = 1518 bytes
When using value 1536 it is possible extend ethernet MAC HEADER up
to 32 bytes. The hardware have support to jumbo frames and it can be
enabled by selecting the value 10240.
Default value: ``1518``
* - ``max-speed``
- ``int``
- .. code-block:: none
This specifies maximum speed in Mbit/s supported by the device. The
gmac driver supports 10Mbit/s and 100Mbit/s. Using 100, as default
value, enables driver to configure 10 and 100Mbit/s speeds.
Default value: ``100``
* - ``phy-connection-type``
- ``string``
- .. code-block:: none
Phy connection type define the physical interface connection between
PHY and MAC. The default value uses gmac register reset value, which
represents Reduced Media-Independent Interface (RMII) mode.
This property must be used with pinctrl-0.
Default value: ``rmii``
Legal values: ``'rmii'``, ``'mii'``
* - ``pinctrl-0``
- ``phandles``
- .. code-block:: none
PIO pin configuration for the various GMAC signals that include GTXCK,
GTXEN, GTX[3..0], GTXER, GRXCK, GRXDV, GRX[3..0], GRXER, GCRS, GCOL,
GMDC, and GMDIO. Which signals are used vary based on if the PHY
connection is MII or RMII (see datasheet for more details). We expect
that the phandles will reference pinctrl nodes. These nodes will have
a nodelabel that matches the Atmel SoC HAL defines and be of the form
p__.
For example the GMAC on SAME7x would be for RMII
pinctrl-0 = <&pd0a_gmac_gtxck &pd1a_gmac_gtxen
&pd2a_gmac_gtx0 &pd3a_gmac_gtx1
&pd4a_gmac_grxdv &pd5a_gmac_grx0
&pd6a_gmac_grx1 &pd7a_gmac_grxer
&pd8a_gmac_gmdc &pd9a_gmac_gmdio>;
This property must be used with phy-connection-type.
* - ``local-mac-address``
- ``uint8-array``
- .. code-block:: none
Specifies the MAC address that was assigned to the network device
* - ``zephyr,random-mac-address``
- ``boolean``
- .. code-block:: none
Use a random MAC address generated when the driver is initialized.
Note that using this choice and rebooting a board may leave stale
MAC address in peers' ARP caches and lead to issues and delays in
communication. (Use "ip neigh flush all" on Linux peers to clear
ARP cache.)
It is driver specific how the OUI octets are handled.
If set we ignore any setting of the local-mac-address property.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "atmel,sam0-gmac" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.