:orphan:
.. raw:: html
.. dtcompatible:: st,stm32wl-subghz-radio
.. _dtbinding_st_stm32wl_subghz_radio:
st,stm32wl-subghz-radio (on spi bus)
####################################
Vendor: :ref:`STMicroelectronics `
Description
***********
.. code-block:: none
STM32WL SUBGHZ Radio
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reset-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO connected to the modem's NRESET signal.
This signal is open-drain, active-low as interpreted by the
modem.
* - ``busy-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO connected to the modem's BUSY signal.
* - ``antenna-enable-gpios``
- ``phandle-array``
- .. code-block:: none
Antenna power enable pin.
* - ``tx-enable-gpios``
- ``phandle-array``
- .. code-block:: none
Antenna switch TX enable GPIO. If set, the driver tracks the
state of the radio and controls the RF switch.
* - ``rx-enable-gpios``
- ``phandle-array``
- .. code-block:: none
Antenna switch RX enable GPIO. If set, the driver tracks the
state of the radio and controls the RF switch.
* - ``dio1-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO connected to DIO1. This GPIO will be used as a generic
IRQ line from the chip.
* - ``dio2-tx-enable``
- ``boolean``
- .. code-block:: none
Use DIO2 to drive an RF switch selecting between the TX and RX
paths. When enabled, DIO2 goes high when the chip is
transmitting.
* - ``dio3-tcxo-voltage``
- ``int``
- .. code-block:: none
TCXO supply voltage controlled by DIO3 if present.
See constants in dt-bindings/lora/sx126x.h.
* - ``tcxo-power-startup-delay-ms``
- ``int``
- .. code-block:: none
Startup delay to let the TCXO stabilize after TCXO power on.
* - ``spi-max-frequency``
- ``int``
- .. code-block:: none
Maximum clock frequency of device's SPI interface in Hz
This property is **required**.
* - ``supply-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
* - ``vin-supply``
- ``phandle``
- .. code-block:: none
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "st,stm32wl-subghz-radio" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``interrupts``
- ``array``
- .. code-block:: none
Position of the "Radio IRQ, Busy" interrupt line.
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.