st,stm32-spi-subghz

Vendor: STMicroelectronics

Description

These nodes are “spi” bus nodes.

STM32 SUBGHZ SPI controller

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

use-subghzspi-nss

boolean

 
Control the SUBGHZPI NSS line using the PWR HAL functions. This is for
the special purpose SUBGHZSPI interface found in the STM32WL series.

This property is required.

pinctrl-0

phandles

 
Pin configuration for SPI signals (MISO, MOSI, SCK and optional NSS).
We expect that the phandles will reference pinctrl nodes.

For example the SPI3 would be
   <&spi3_sck_pc10 &spi3_miso_pc11 &spi3_mosi_pc12>;

Example with NSS Pin
   <&spi3_sck_pc10 &spi3_miso_pc11 &spi3_mosi_pc12 &spi3_nss_pa15>;

clock-frequency

int

 
Clock frequency the SPI peripheral is being driven at, in Hz.

cs-gpios

phandle-array

 
An array of chip select GPIOs to use. Each element
in the array specifies a GPIO. The index in the array
corresponds to the child node that the CS gpio controls.

Example:

  spi@... {
          cs-gpios = <&gpio0 23 GPIO_ACTIVE_LOW>,
                        <&gpio1 10 GPIO_ACTIVE_LOW>,
                        ...;

          spi-device@0 {
                  reg = <0>;
                  ...
          };
          spi-device@1 {
                  reg = <1>;
                  ...
          };
          ...
  };

The child node "spi-device@0" specifies a SPI device with
chip select controller gpio0, pin 23, and devicetree
GPIO flags GPIO_ACTIVE_LOW. Similarly, "spi-device@1" has CS GPIO
controller gpio1, pin 10, and flags GPIO_ACTIVE_LOW. Additional
devices can be configured in the same way.

If unsure about the flags cell, GPIO_ACTIVE_LOW is generally a safe
choice for a typical "CSn" pin. GPIO_ACTIVE_HIGH may be used if
intervening hardware inverts the signal to the peripheral device or
the line itself is active high.

If this property is not defined, no chip select GPIOs are set.
SPI controllers with dedicated CS pins do not need to define
the cs-gpios property.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “st,stm32-spi-subghz” compatible.

Name

Type

Details

reg

array

 
register space

This property is required.

See Important properties for more information.

interrupts

array

 
interrupts for device

This property is required.

See Important properties for more information.

#address-cells

int

 
number of address cells in reg property

This property is required.

Constant value: 1

#size-cells

int

 
number of size cells in reg property

This property is required.

label

string

 
Human readable string describing the device (used as device_get_binding() argument)

This property is required.

See Important properties for more information.

status

string

 
indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

 
compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

 
name of each register space

interrupts-extended

compound

 
extended interrupt specifier for device

interrupt-names

string-array

 
name of each interrupt

interrupt-parent

phandle

 
phandle to interrupt controller node

clocks

phandle-array

 
Clock gate information

clock-names

string-array

 
name of each clock

dmas

phandle-array

 
DMA channels specifiers

dma-names

string-array

 
Provided names of DMA channel specifiers

io-channels

phandle-array

 
IO channels specifiers

io-channel-names

string-array

 
Provided names of IO channel specifiers

wakeup-source

boolean

 
Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.