:orphan:

.. title:: CONFIG_GPIO_NPCX

.. kconfig:: CONFIG_GPIO_NPCX

CONFIG_GPIO_NPCX
################

*Nuvoton NPCX embedded controller (EC) gpio driver*

Type: ``bool``

Help
====

.. code-block:: none

    Enable support for NPCX GPIO driver.

Help
====

.. code-block:: none

    Enable support for NPCX GPIO driver. In NPCX9 series, it includes 16
    ports that support input/output, input-only and output-only
    configurations.

Help
====

.. code-block:: none

    Enable support for NPCX GPIO driver.

Help
====

.. code-block:: none

    Enable support for NPCX GPIO driver. In NPCX9 series, it includes 16
    ports that support input/output, input-only and output-only
    configurations.

Help
====

.. code-block:: none

    This option enables the GPIO driver for NPCX family of
    processors.
    Say y if you wish to use serial port on NPCX MCU.

Direct dependencies
===================

(\ :kconfig:`GPIO <CONFIG_GPIO>` && \ :kconfig:`SOC_SERIES_NPCX7 <CONFIG_SOC_SERIES_NPCX7>`) || (\ :kconfig:`GPIO <CONFIG_GPIO>` && \ :kconfig:`SOC_SERIES_NPCX9 <CONFIG_SOC_SERIES_NPCX9>`) || (\ :kconfig:`GPIO <CONFIG_GPIO>` && \ :kconfig:`SOC_SERIES_NPCX7 <CONFIG_SOC_SERIES_NPCX7>`) || (\ :kconfig:`GPIO <CONFIG_GPIO>` && \ :kconfig:`SOC_SERIES_NPCX9 <CONFIG_SOC_SERIES_NPCX9>`) || (\ :kconfig:`SOC_FAMILY_NPCX <CONFIG_SOC_FAMILY_NPCX>` && \ :kconfig:`GPIO <CONFIG_GPIO>`)

*(Includes any dependencies from ifs and menus.)*

Defaults
========

- y
- y
- y
- y

Kconfig definitions
===================



At ``<Zephyr SoC>/arm/nuvoton_npcx/npcx7/Kconfig.defconfig.series:31``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:25`` → ``<BuildDir>/kconfig/Kconfig.soc.defconfig:1`` → ``<Zephyr SoC>/arm/nuvoton_npcx/Kconfig.defconfig:6``

Menu path: (Top)

.. code-block:: kconfig

    config GPIO_NPCX
    	bool
    	default y
    	depends on GPIO && SOC_SERIES_NPCX7
    	help
    	  Enable support for NPCX GPIO driver.

----

At ``<Zephyr SoC>/arm/nuvoton_npcx/npcx9/Kconfig.defconfig.series:36``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:25`` → ``<BuildDir>/kconfig/Kconfig.soc.defconfig:1`` → ``<Zephyr SoC>/arm/nuvoton_npcx/Kconfig.defconfig:6``

Menu path: (Top)

.. code-block:: kconfig

    config GPIO_NPCX
    	bool
    	default y
    	depends on GPIO && SOC_SERIES_NPCX9
    	help
    	  Enable support for NPCX GPIO driver. In NPCX9 series, it includes 16
    	  ports that support input/output, input-only and output-only
    	  configurations.

----

At ``<Zephyr SoC>/arm/nuvoton_npcx/npcx7/Kconfig.defconfig.series:31``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:27`` → ``<Zephyr SoC>/arm/nuvoton_npcx/Kconfig.defconfig:6``

Menu path: (Top)

.. code-block:: kconfig

    config GPIO_NPCX
    	bool
    	default y
    	depends on GPIO && SOC_SERIES_NPCX7
    	help
    	  Enable support for NPCX GPIO driver.

----

At ``<Zephyr SoC>/arm/nuvoton_npcx/npcx9/Kconfig.defconfig.series:36``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:27`` → ``<Zephyr SoC>/arm/nuvoton_npcx/Kconfig.defconfig:6``

Menu path: (Top)

.. code-block:: kconfig

    config GPIO_NPCX
    	bool
    	default y
    	depends on GPIO && SOC_SERIES_NPCX9
    	help
    	  Enable support for NPCX GPIO driver. In NPCX9 series, it includes 16
    	  ports that support input/output, input-only and output-only
    	  configurations.

----

At ``<Zephyr Driver>/gpio/Kconfig.npcx:6``

Included via ``Kconfig:8`` → ``Kconfig.zephyr:42`` → ``<Zephyr Driver>/Kconfig:36`` → ``<Zephyr Driver>/gpio/Kconfig:82``

Menu path: (Top) → Device Drivers → GPIO Drivers

.. code-block:: kconfig

    config GPIO_NPCX
    	bool "Nuvoton NPCX embedded controller (EC) gpio driver"
    	depends on SOC_FAMILY_NPCX && GPIO
    	help
    	  This option enables the GPIO driver for NPCX family of
    	  processors.
    	  Say y if you wish to use serial port on NPCX MCU.

*(The 'depends on' condition includes propagated dependencies from ifs and menus.)*