:orphan:
.. raw:: html
.. dtcompatible:: atmel-xplained-pro-header
.. _dtbinding_atmel_xplained_pro_header:
atmel-xplained-pro-header
#########################
Vendor: :ref:`Generic or vendor-independent `
Description
***********
.. code-block:: none
GPIO pins exposed on Atmel Xplained Pro headers.
The Xplained Pro layout provide a standard 20 pin header. A board can have
one or more headers and can share pins. The extension headers are given
names EXTn where n ϵ [1…7], n is determined by which ID pin is connected
to the embedded debugger. A header with ID7 signal from the embedded
debugger connected should be called EXT7. PWR, EXT1, EXT2 and EXT3 are
standard extension headers that have a predefined position according to the
list below:
* PWR is right angled at the top right hand side of the board. This
header must always be implemented.
* EXT1 is right angled at the top right hand side of the board, located
below the PWR header. This header must always be present.
* EXT2 is right angled and at the bottom right hand side of the board.
This header is mandatory for medium and large boards and should not be
implemented on small boards.
* EXT3 is right angled pointing downwards
All MCU boards have to implement at least PWR, EXT1, EXT2 (on medium and
large boards), and EXT3. EXT4 to EXT7 can be placed differently depending
on the board design. EXT4 to EXT7 can either be standard extension headers
or application specific headers.
Documentation:
* https://www.microchip.com/development-tools/xplained-boards
* http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-42091-Atmel-Xplained-Pro-Hardware-Development-Kit_User%20Guide.pdf
This binding provides a nexus mapping for 20 pins where pins are disposed
to have a even and odd column:
Connector
Bind Pin Name Pin Pin Pin Name Bind
ID 1 2 GND
0 ADC(+) 3 4 ADC(-) 1
2 UART(RTS)/GPIO1 5 6 UART(CTS)/GPIO2 3
4 PWM(+) 7 8 PWM(-) 5
6 IRQ/GPIO3 9 10 SPI(CS1)/GPIO4 7
8 I2C(SDA) 11 12 I2C(SCL) 9
10 UART(RX) 13 14 UART(TX) 11
12 SPI(CS0) 15 16 SPI(MOSI) 13
14 SPI(MISO) 17 18 SPI(SCK) 15
GND 19 20 VDD(+3.3V)
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``gpio-map``
- ``compound``
- This property is **required**.
* - ``gpio-map-mask``
- ``compound``
-
* - ``gpio-map-pass-thru``
- ``compound``
-
* - ``#gpio-cells``
- ``int``
- .. code-block:: none
Number of items to expect in a GPIO specifier
This property is **required**.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "atmel-xplained-pro-header" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg``
- ``array``
- .. code-block:: none
register space
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
See :ref:`zephyr:dt-important-props` for more information.
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.