:orphan:
.. raw:: html
.. dtcompatible:: nordic,nrf-i2s
.. _dtbinding_nordic_nrf_i2s:
nordic,nrf-i2s
##############
Vendor: :ref:`Nordic Semiconductor `
Description
***********
These nodes are "i2s" bus nodes.
.. code-block:: none
Nordic I2S (Inter-IC sound interface)
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``sck-pin``
- ``int``
- .. code-block:: none
IMPORTANT: This option will only be used if the new pin control driver
is not enabled. It will be deprecated in the future.
The SCK pin to use.
For pins P0.0 through P0.31, use the pin number. For example,
to use P0.16 for SCK, set:
sck-pin = <16>;
For pins P1.0 through P1.31, add 32 to the pin number. For
example, to use P1.2 for SCK, set:
sck-pin = <34>; /* 32 + 2 */
* - ``lrck-pin``
- ``int``
- .. code-block:: none
IMPORTANT: This option will only be used if the new pin control driver
is not enabled. It will be deprecated in the future.
The LRCK pin to use. The pin numbering scheme is the same as
the sck-pin property's.
* - ``sdout-pin``
- ``int``
- .. code-block:: none
IMPORTANT: This option will only be used if the new pin control driver
is not enabled. It will be deprecated in the future.
The SDOUT pin to use. The pin numbering scheme is the same as
the sck-pin property's.
* - ``sdin-pin``
- ``int``
- .. code-block:: none
IMPORTANT: This option will only be used if the new pin control driver
is not enabled. It will be deprecated in the future.
The SDIN pin to use. The pin numbering scheme is the same as
the sck-pin property's.
* - ``mck-pin``
- ``int``
- .. code-block:: none
IMPORTANT: This option will only be used if the new pin control driver
is not enabled. It will be deprecated in the future.
The MCK pin to use. The pin numbering scheme is the same as
the sck-pin property's.
* - ``clock-source``
- ``string``
- .. code-block:: none
Clock source to be used by the I2S peripheral for the master clock
(MCK) generator. The generator is only needed when the I2S peripheral
is operating in Master mode. The following options are available:
- "PCLK32M": 32 MHz peripheral clock, synchronous to HFCLK
- "PCLK32M_HFXO": PCLK32M running off the 32 MHz crystal oscillator
(HFXO) for better clock accuracy and jitter performance
- "ACLK": Audio PLL clock with configurable frequency (frequency for
this clock must be set via the "hfclkaudio-frequency" property
in the "nordic,nrf-clock" node); this clock source is only available
in the nRF53 Series SoCs and it requires the use of HFXO
Default value: ``PCLK32M_HFXO``
Legal values: ``'PCLK32M'``, ``'PCLK32M_HFXO'``, ``'ACLK'``
* - ``pinctrl-0``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
* - ``pinctrl-1``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the second state. See pinctrl-0.
* - ``pinctrl-2``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the third state. See pinctrl-0.
* - ``pinctrl-3``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fourth state. See pinctrl-0.
* - ``pinctrl-4``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fifth state. See pinctrl-0.
* - ``pinctrl-names``
- ``string-array``
- .. code-block:: none
Names for the provided states. The number of names needs to match the
number of states.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "nordic,nrf-i2s" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
This property is **required**.
Constant value: ``1``
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
This property is **required**.
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.