:orphan:
.. raw:: html
.. dtcompatible:: st,stm32-fmc-sdram
.. _dtbinding_st_stm32_fmc_sdram:
st,stm32-fmc-sdram
##################
Vendor: :ref:`STMicroelectronics `
Description
***********
.. code-block:: none
STM32 Flexible Memory Controller (SDRAM controller).
The FMC SDRAM controller can be used to interface with external SDRAM
memories. Up to 2 SDRAM banks are supported with independent configuration. It
is worth to note that while settings are independent, some are shared or are
required to be set according to the most constraining device. Refer to the
properties description or the datasheet for more details.
The FMC SDRAM controller is defined below the FMC node and SDRAM banks are
defined as child nodes of the FMC SDRAM node. You can either have bank 1 (@0),
bank 2 (@1) or both. You can enable the FMC SDRAM controller in your board
DeviceTree file like this:
&fmc {
status = "okay";
pinctrl-0 = <&fmc_nbl0_pe0 &fmc_nbl1_pe1 &fmc_nbl2_pi4...>;
sdram {
status = "okay";
power-up-delay = <100>;
num-auto-refresh = <8>;
mode-register = <0x220>;
refresh-rate = <603>;
bank@0 {
reg = <0>;
st,sdram-control = ;
st,sdram-timing = <2 6 4 6 2 2 2>;
};
bank@1 {
reg = <1>;
...
};
};
};
Note that you will find definitions for the st,sdram-control field at
dt-bindings/memory-controller/stm32-fmc-sdram.h. This file is already included
in the SoC DeviceTree files.
Finally, in order to make the memory available you will need to define new
memory device/s in DeviceTree:
sdram1: sdram@c0000000 {
compatible = "zephyr,memory-region", "mmio-sram";
device_type = "memory";
reg = <0xc000000 DT_SIZE_M(X)>;
zephyr,memory-region = "SDRAM1";
};
sdram2: sdram@d0000000 {
compatible = "zephyr,memory-region", "mmio-sram";
device_type = "memory";
reg = <0xd000000 DT_SIZE_M(X)>;
zephyr,memory-region = "SDRAM2";
};
It is important to use sdram1 and sdram2 node labels for bank 1 and bank 2
respectively. Memory addresses are 0xc0000000 and 0xd0000000 for bank 1 and
bank 2 respectively.
Properties
**********
Top level properties
====================
These property descriptions apply to "st,stm32-fmc-sdram"
nodes themselves. This page also describes child node
properties in the following sections.
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``power-up-delay``
- ``int``
- .. code-block:: none
Power-up delay in microseconds.
Default value: ``100``
* - ``num-auto-refresh``
- ``int``
- .. code-block:: none
Number of auto-refresh commands issued.
Default value: ``8``
* - ``mode-register``
- ``int``
- .. code-block:: none
A 14-bit field that defines the SDRAM Mode Register content. The mode register bits are also used to program the extended mode register for mobile SDRAM.
This property is **required**.
* - ``refresh-rate``
- ``int``
- .. code-block:: none
A 13-bit field defines the refresh rate of the SDRAM device. It is expressed in number of memory clock cycles. It must be set at least to 41 SDRAM clock cycles.
This property is **required**.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "st,stm32-fmc-sdram" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
This property is **required**.
Constant value: ``1``
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
This property is **required**.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg``
- ``array``
- .. code-block:: none
register space
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
Child node properties
=====================
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``int``
- This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``st,sdram-control``
- ``array``
- .. code-block:: none
SDRAM control configuration. Expected fields, in order, are,
- NC: Number of bits of a column address.
- NR: Number of bits of a row address.
- MWID: Memory device width.
- NB: Number of internal banks.
- CAS: SDRAM CAS latency in number of memory clock cycles.
- SDCLK: SDRAM clock period. If two SDRAM devices are used both should
have the same value.
- RBURST: Enable burst read mode. If two SDRAM devices are used both
should have the same value.
- RPIPE: Delay, in fmc_ker_ck clock cycles, for reading data after CAS
latency. If two SDRAM devices are used both should have the same
value.
This property is **required**.
* - ``st,sdram-timing``
- ``array``
- .. code-block:: none
SDRAM timing configuration. Expected fields, in order, are,
- TMRD: Delay between a Load Mode Register command and an Active or
Refresh command in number of memory clock cycles.
- TXSR: Delay from releasing the Self-refresh command to issuing the
Activate command in number of memory clock cycles. If two SDRAM
devices are used, the FMC_SDTR1 and FMC_SDTR2 must be programmed with
the same TXSR timing corresponding to the slowest SDRAM device
- TRAS: Minimum Self-refresh period in number of memory clock cycles.
- TRC: Delay between the Refresh command and the Activate command, as
well as the delay between two consecutive Refresh commands. It is
expressed in number of memory clock cycles. If two SDRAM devices are
used, the TRC must be programmed with the timings of the slowest
device in both banks.
- TWP: Delay between a Write and a Precharge command in number of memory
clock cycles
- TRP: Delay between a Precharge command and another command in number
of memory clock cycles. If two SDRAM devices are used, the TRP must be
programmed with the timing of the slowest device in both banks.
- TRCD: Delay between the Activate command and a Read/Write command in
number of memory clock cycles.
This property is **required**.