:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: ti,cc13xx-cc26xx-pinctrl
.. _dtbinding_ti_cc13xx_cc26xx_pinctrl:

ti,cc13xx-cc26xx-pinctrl
########################

Vendor: :ref:`Texas Instruments <dt_vendor_ti>`

Description
***********



.. code-block:: none

   TI SimpleLink CC13xx / CC26xx pinctrl node.

   Device pin configuration should be placed in the child nodes of this node.
   Populate the 'pinmux' field with a pair consisting of a pin number and its IO
   functions.

   The node has the 'pinctrl' node label set in your SoC's devicetree,
   so you can modify it like this:

     &pinctrl {
             /* your modifications go here */
     };

   All device pin configurations should be placed in child nodes of the
   'pinctrl' node, as in the i2c0 example shown at the end.

   Here is a list of
   supported standard pin properties:

   - bias-disable: Disable pull-up/down.
   - bias-pull-down: Enable pull-down resistor.
   - bias-pull-up: Enable pull-up resistor.
   - drive-open-drain: Output driver is open-drain.
   - drive-open-drain: Output driver is open-source.
   - input-enable: enable input.
   - input-schmitt-enable: enable input schmitt circuit.

   An example for CC13XX family, include the chip level pinctrl
   DTSI file in the board level DTS:

     #include <dt-bindings/pinctrl/cc13xx_cc26xx-pinctrl.h>

   We want to configure the I2C pins to open drain, with pullup enabled
   and input enabled.

   To change a pin's pinctrl default properties add a reference to the
   pin in the board's DTS file and set the properties.

     &i2c0 {
       pinctrl-0 = <&i2c0_scl_default &i2c0_sda_default>;
       pinctrl-1 = <&i2c0_scl_sleep &i2c0_sda_sleep>;
       pinctrl-names = "default", "sleep";
     }

   The i2c0_scl_default corresponds to the following in the board dts file:

     &pinctrl {
       i2c0_scl_default: i2c0_scl_default {
         pinmux = <4 IOC_PORT_MCU_I2C_MSSCL>;
         bias-pull-up;
         drive-open-drain;
         input-enable;
       };
     };

Properties
**********

Top level properties
====================


These property descriptions apply to "ti,cc13xx-cc26xx-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "ti,cc13xx-cc26xx-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)


             See :ref:`zephyr:dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.






Child node properties
=====================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``pinmux``
     - ``array``
     - .. code-block:: none

          CC13XX/CC26XX pin's configuration (IO pin, IO function).



       This property is **required**.

   * - ``bias-disable``
     - ``boolean``
     - .. code-block:: none

          disable any pin bias


   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)


   * - ``drive-open-source``
     - ``boolean``
     - .. code-block:: none

          drive with open source (hardware OR)


   * - ``input-enable``
     - ``boolean``
     - .. code-block:: none

          enable input on pin (no effect on output, such as enabling an input
          buffer)



   * - ``input-schmitt-enable``
     - ``boolean``
     - .. code-block:: none

          enable schmitt-trigger mode