nxp,s32-spi

Vendor: NXP Semiconductors

Description

These nodes are “spi” bus nodes.

NXP S32 SPI controller

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

num-cs

int

 
The number of the Chip Select signals.

This property is required.

clock-frequency

int

 
Module clock frequency in Hz.

This property is required.

pinctrl-0

phandles

 
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.

This property is required.

pinctrl-names

string-array

 
Names for the provided states. The number of names needs to match the
number of states.

This property is required.

slave

boolean

 
Select if the SPI module is intended to be used in slave mode.

spi-sck-cs-delay

int

 
A delay in nanoseconds between the stop of clock signal and
deactivating Chip Select at the stop of transfer. If CS remains
asserted between transfer, this delay will be inserted between transfer.
If not set, the minimum supported delay is used.
This value will affect to all inner CS signals of SPI module when active.
This value will not be applied for CS lines controlled by GPIO.

spi-cs-sck-delay

int

 
A delay in nanoseconds between activating Chip Select and the start
of clock signal at the start of transfer. If CS remains asserted
between transfer, this delay will be inserted between transfer.
If not set, the minimum supported delay is used.
This value will affect to all inner CS signals of SPI module when active.
This value will not be applied for CS lines controlled by GPIO.

spi-cs-cs-delay

int

 
A delay in nanoseconds between deactivating Chip Select at the stop
of previous transfer and activating Chip Select at the start of
next transfer. If CS remains asserted between transfer, this delay
will not be inserted.
If not set, the minimum supported delay is used.
This value will affect to all inner CS signals of SPI module when active.
This value will not be applied for CS lines controlled by GPIO.

cs-gpios

phandle-array

 
An array of chip select GPIOs to use. Each element
in the array specifies a GPIO. The index in the array
corresponds to the child node that the CS gpio controls.

Example:

  spi@... {
          cs-gpios = <&gpio0 23 GPIO_ACTIVE_LOW>,
                        <&gpio1 10 GPIO_ACTIVE_LOW>,
                        ...;

          spi-device@0 {
                  reg = <0>;
                  ...
          };
          spi-device@1 {
                  reg = <1>;
                  ...
          };
          ...
  };

The child node "spi-device@0" specifies a SPI device with
chip select controller gpio0, pin 23, and devicetree
GPIO flags GPIO_ACTIVE_LOW. Similarly, "spi-device@1" has CS GPIO
controller gpio1, pin 10, and flags GPIO_ACTIVE_LOW. Additional
devices can be configured in the same way.

If unsure about the flags cell, GPIO_ACTIVE_LOW is generally a safe
choice for a typical "CSn" pin. GPIO_ACTIVE_HIGH may be used if
intervening hardware inverts the signal to the peripheral device or
the line itself is active high.

If this property is not defined, no chip select GPIOs are set.
SPI controllers with dedicated CS pins do not need to define
the cs-gpios property.

pinctrl-1

phandles

 
Pin configuration/s for the second state. See pinctrl-0.

pinctrl-2

phandles

 
Pin configuration/s for the third state. See pinctrl-0.

pinctrl-3

phandles

 
Pin configuration/s for the fourth state. See pinctrl-0.

pinctrl-4

phandles

 
Pin configuration/s for the fifth state. See pinctrl-0.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,s32-spi” compatible.

Name

Type

Details

reg

array

 
register space

This property is required.

See Important properties for more information.

interrupts

array

 
interrupts for device

This property is required.

See Important properties for more information.

#address-cells

int

 
number of address cells in reg property

This property is required.

Constant value: 1

#size-cells

int

 
number of size cells in reg property

This property is required.

status

string

 
indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

 
compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

 
name of each register space

interrupts-extended

compound

 
extended interrupt specifier for device

interrupt-names

string-array

 
name of each interrupt

interrupt-parent

phandle

 
phandle to interrupt controller node

label

string

 
Human readable string describing the device (used as device_get_binding() argument)

See Important properties for more information.

This property is deprecated.

clocks

phandle-array

 
Clock gate information

clock-names

string-array

 
name of each clock

dmas

phandle-array

 
DMA channels specifiers

dma-names

string-array

 
Provided names of DMA channel specifiers

io-channels

phandle-array

 
IO channels specifiers

io-channel-names

string-array

 
Provided names of IO channel specifiers

mboxes

phandle-array

 
mailbox / IPM channels specifiers

mbox-names

string-array

 
Provided names of mailbox / IPM channel specifiers

wakeup-source

boolean

 
Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

power-domain

phandle

 
Power domain the device belongs to.

The device will be notified when the power domain it belongs to is either
suspended or resumed.