:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: ti,cc32xx-pinctrl
.. _dtbinding_ti_cc32xx_pinctrl:

ti,cc32xx-pinctrl
#################

Vendor: :ref:`Texas Instruments <dt_vendor_ti>`

Description
***********



.. code-block:: none

   The TI CC32XX pin controller is a singleton node responsible for controlling
   pin function selection and pin properties. For example, you can
   use this node to route UART0 RX to pin 55 and enable the pull-up resistor
   on the pin.

   The node has the 'pinctrl' node label set in your SoC's devicetree,
   so you can modify it like this:

     &pinctrl {
             /* your modifications go here */
     };

   All device pin configurations should be placed in child nodes of the
   'pinctrl' node, as shown in this example:

     /* You can put this in places like a board-pinctrl.dtsi file in
      * your board directory, or a devicetree overlay in your application.
      */

     /* include pre-defined combinations for the SoC variant used by the board */
     #include <dt-bindings/pinctrl/gd32f450i(g-i-k)xx-pinctrl.h>

     &pinctrl {
       /* configuration for the uart0 "default" state */
       uart0_default: uart0_default {
         /* group 1 */
         group1 {
           /* configure pin 55 as UART0 TX and pin 61 as UART0 CTS */
           pinmux = <UART0_TX_P55>, <UART0_CTS_P61>;
         };
         /* group 2 */
         group2 {
           /* configure pin 57 as UART0 RX and pin 62 as UART0 RTS  */
           pinmux = <UART0_RX_P57>, <UART0_RTS_P62>;
           /* both pin 57 and 62 have pull-up enabled */
           bias-pull-up;
         };
       };

   The 'uart0_default' child node encodes the pin configurations for a
   particular state of a device; in this case, the default (that is, active)
   state.

   As shown, pin configurations are organized in groups within each child node.
   Each group can specify a list of pin function selections in the 'pinmux'
   property.

   A group can also specify shared pin properties common to all the specified
   pins, such as the 'bias-pull-up' property in group 2. Here is a list of
   supported standard pin properties:

   - drive-push-pull: Push-pull drive mode (default, not required).
   - drive-open-drain: Open-drain drive mode.
   - bias-disable: Disable pull-up/down (default, not required).
   - bias-pull-up: Enable pull-up resistor.
   - bias-pull-down: Enable pull-down resistor.
   - drive-strength: Configure drive strength in mA (defaults to 6mA, IC default).

   Note that drive and bias options are mutually exclusive.

   To link pin configurations with a device, use a pinctrl-N property for some
   number N, like this example you could place in your board's DTS file:

      #include "board-pinctrl.dtsi"

      &uart0 {
            pinctrl-0 = <&uart0_default>
            pinctrl-names = "default";
      };

Properties
**********

Top level properties
====================


These property descriptions apply to "ti,cc32xx-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "ti,cc32xx-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`zephyr:dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.






Grandchild node properties
==========================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``pinmux``
     - ``array``
     - .. code-block:: none

          An array of pins sharing the same group properties. The pins should
          be defined using pre-defined macros or, alternatively, using the
          TI_CC32XX_PINMUX helper macro.



       This property is **required**.

   * - ``drive-strength``
     - ``int``
     - .. code-block:: none

          maximum sink or source current in mA


       Default value: ``6``

       Legal values: ``0``, ``2``, ``4``, ``6``, ``8``, ``10``, ``12``, ``14``

   * - ``bias-disable``
     - ``boolean``
     - .. code-block:: none

          disable any pin bias


   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-push-pull``
     - ``boolean``
     - .. code-block:: none

          drive actively high and low


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)