:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: ti,tmag5273
.. _dtbinding_ti_tmag5273:

ti,tmag5273 (on i2c bus)
########################

Vendor: :ref:`Texas Instruments <dt_vendor_ti>`

Description
***********



.. code-block:: none

   Texas Instruments TMAG5273 Low-Power Linear 3D Hall-Effect Sensor with an I2C interface.

   See the specification for the default I2C address.

   The specification of the sensor can be found at:
     https://www.ti.com/lit/ds/symlink/tmag5273.pdf

     When setting the enum properties in a .dts or .dtsi file you may
     include tmag5273.h and use the macros defined there.

     Example:
     #include <zephyr/dt-bindings/sensor/tmag5273.h>

     tmag5273: tmag5273@0 {
       ...
       axis = <TMAG5273_DT_AXIS_XYZ>;
       range = <TMAG5273_DT_AXIS_RANGE_HIGH>;
     };

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``operation-mode``
           - ``int``
           - .. code-block:: none

                Sensor mode used if set to "active".
                Defaults to continuous sampling (TMAG5273_DT_OPER_MODE_CONTINUOUS).

                - 0 # TMAG5273_DT_OPER_MODE_CONTINUOUS (continuous)
                - 1 # TMAG5273_DT_OPER_MODE_STANDBY    (standby)



             Legal values: ``0``, ``1``

         * - ``axis``
           - ``int``
           - .. code-block:: none

                Magnet axis channel inputs.
                Defaults to measure all axis (TMAG5273_DT_AXIS_XYZ).

                - 0  # TMAG5273_DT_AXIS_NONE
                - 1  # TMAG5273_DT_AXIS_X
                - 2  # TMAG5273_DT_AXIS_Y
                - 3  # TMAG5273_DT_AXIS_Z
                - 4  # TMAG5273_DT_AXIS_XY
                - 5  # TMAG5273_DT_AXIS_XZ
                - 6  # TMAG5273_DT_AXIS_YZ
                - 7  # TMAG5273_DT_AXIS_XYZ
                - 8  # TMAG5273_DT_AXIS_XYX (pseudo-simultaneous sampling)
                - 9  # TMAG5273_DT_AXIS_YXY (pseudo-simultaneous sampling)
                - 10 # TMAG5273_DT_AXIS_YZY (pseudo-simultaneous sampling)
                - 11 # TMAG5273_DT_AXIS_XZX (pseudo-simultaneous sampling)



             Default value: ``7``

             Legal values: ``0``, ``1``, ``2``, ``3``, ``4``, ``5``, ``6``, ``7``, ``8``, ``9``, ``10``, ``11``

         * - ``temperature``
           - ``boolean``
           - .. code-block:: none

                Select for temperature measurement.



         * - ``range``
           - ``int``
           - .. code-block:: none

                XYZ-measurement range for magnetic-field value.
                Defaults to lower range (higher resolution; TMAG5273_DT_AXIS_RANGE_LOW).

                - 0 # TMAG5273_DT_AXIS_RANGE_LOW      (+/-40 mT (TMAG5273A1) or +/-133 mT (TMAG5273A2))
                - 1 # TMAG5273_DT_AXIS_RANGE_HIGH     (+/-80 mT (TMAG5273A1) or +/-266 mT (TMAG5273A2))
                - 2 # TMAG5273_DT_AXIS_RANGE_RUNTIME  (@runtime (initial value is: "high"))



             Default value: ``1``

             Legal values: ``0``, ``1``, ``2``

         * - ``int-gpios``
           - ``phandle-array``
           - .. code-block:: none

                The INT signal connection.

                The signal is active-low as produced by the sensor.
                Either used for interrupt signaling, or triggering a conversion.



         * - ``temperature-coefficient``
           - ``int``
           - .. code-block:: none

                Selects the magnet temperature coefficient.
                Defaults to none (TMAG5273_DT_TEMP_COEFF_NONE).

                  - 0 # TMAG5273_DT_TEMP_COEFF_NONE    (none)
                  - 1 # TMAG5273_DT_TEMP_COEFF_NDBFE   (0.12 %/deg C (NdBFe))
                  - 2 # TMAG5273_DT_TEMP_COEFF_CERAMIC (0.2 %/deg C (Ceramic))

                Ignored if temperature is not measured.



             Legal values: ``0``, ``1``, ``2``

         * - ``trigger-conversion-via-int``
           - ``boolean``
           - .. code-block:: none

                Selects initiation of a single conversion based on a trigger via
                the INT-pin if enabled, and via I2C-command if disabled.

                Used in "standby"-, "wakeup-and-sleep"- and "sleep"-mode.
                Using I2C-conversion trigger may result in (handled) I2C-errors.



         * - ``angle-magnitude-axis``
           - ``int``
           - .. code-block:: none

                Enables angle calculation, magnetic gain, and offset corrections
                between two selected magnetic channels.
                Defaults to no additional calculations (TMAG5273_DT_ANGLE_MAG_NONE).

                - 0 # TMAG5273_DT_ANGLE_MAG_NONE    (deactivated)
                - 1 # TMAG5273_DT_ANGLE_MAG_XY      (x/y)
                - 2 # TMAG5273_DT_ANGLE_MAG_YZ      (y/z)
                - 3 # TMAG5273_DT_ANGLE_MAG_XZ      (x/z)
                - 4 # TMAG5273_DT_ANGLE_MAG_RUNTIME (@runtime (initial value is: "deactivated"))



             Legal values: ``0``, ``1``, ``2``, ``3``, ``4``

         * - ``ch-mag-gain-correction``
           - ``int``
           - .. code-block:: none

                Channel for the magnitude gain correction.
                Defaults to 1st channel.

                  - 0 # TMAG5273_DT_CORRECTION_CH_1 (1st channel)
                  - 1 # TMAG5273_DT_CORRECTION_CH_2 (2nd channel)

                Only active if angle-magnitude-calculation is active.



             Legal values: ``0``, ``1``

         * - ``average-mode``
           - ``int``
           - .. code-block:: none

                Enables additional sampling of the sensor data to reduce the noise effect
                (or to increase resolution).

                Note that averaging will influence the output data rate.
                Defaults to 2x averaging (TMAG5273_DT_AVERAGING_2X).

                - 0 # TMAG5273_DT_AVERAGING_NONE  (10.0-kSPS (3-axes) or 20-kSPS   (1 axis))
                - 1 # TMAG5273_DT_AVERAGING_2X    (5.7-kSPS  (3-axes) or 13.3-kSPS (1 axis))
                - 2 # TMAG5273_DT_AVERAGING_4X    (3.1-kSPS  (3-axes) or 8.0-kSPS  (1 axis))
                - 3 # TMAG5273_DT_AVERAGING_8X    (1.6-kSPS  (3-axes) or 4.4-kSPS  (1 axis))
                - 4 # TMAG5273_DT_AVERAGING_16X   (0.8-kSPS  (3-axes) or 2.4-kSPS  (1 axis))
                - 5 # TMAG5273_DT_AVERAGING_32X   (0.4-kSPS  (3-axes) or 1.2-kSPS  (1 axis))



             Default value: ``1``

             Legal values: ``0``, ``1``, ``2``, ``3``, ``4``, ``5``

         * - ``crc-enabled``
           - ``boolean``
           - .. code-block:: none

                Activate I2C CRC byte to be sent.



         * - ``low-noise``
           - ``boolean``
           - .. code-block:: none

                Select low-noise mode when enabled, and low-power mode when disabled.



         * - ``ignore-diag-fail``
           - ``boolean``
           - .. code-block:: none

                Ignore detected diagnostic fail.
                According to the manual, this should be done if VCC < 2.3V.



         * - ``friendly-name``
           - ``string``
           - .. code-block:: none

                Human readable string describing the sensor. It can be used to
                distinguish multiple instances of the same model (e.g., lid accelerometer
                vs. base accelerometer in a laptop) to a host operating system.

                This property is defined in the Generic Sensor Property Usages of the HID
                Usage Tables specification
                (https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).



         * - ``supply-gpios``
           - ``phandle-array``
           - .. code-block:: none

                GPIO specifier that controls power to the device.

                This property should be provided when the device has a dedicated
                switch that controls power to the device.  The supply state is
                entirely the responsibility of the device driver.

                Contrast with vin-supply.



         * - ``vin-supply``
           - ``phandle``
           - .. code-block:: none

                Reference to the regulator that controls power to the device.
                The referenced devicetree node must have a regulator compatible.

                This property should be provided when device power is supplied
                by a shared regulator.  The supply state is dependent on the
                request status of all devices fed by the regulator.

                Contrast with supply-gpios.  If both properties are provided
                then the regulator must be requested before the supply GPIOS is
                set to an active state, and the supply GPIOS must be set to an
                inactive state before releasing the regulator.





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "ti,tmag5273" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`zephyr:dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.