:orphan:
.. raw:: html
.. dtcompatible:: infineon,xmc4xxx-uart
.. _dtbinding_infineon_xmc4xxx_uart:
infineon,xmc4xxx-uart
#####################
Vendor: :ref:`Infineon Technologies `
Description
***********
These nodes are "uart" bus nodes.
.. code-block:: none
INFINEON XMC4XXX UART
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``clock-frequency``
- ``int``
- .. code-block:: none
Clock frequency information for UART operation
* - ``current-speed``
- ``int``
- .. code-block:: none
Initial baud rate setting for UART
* - ``hw-flow-control``
- ``boolean``
- .. code-block:: none
Set to enable RTS/CTS flow control at boot time
* - ``parity``
- ``string``
- .. code-block:: none
Configures the parity of the adapter. Enumeration id 0 for none, 1 for odd
and 2 for even parity. Default to none if not specified.
Legal values: ``'none'``, ``'odd'``, ``'even'``
* - ``stop-bits``
- ``string``
- .. code-block:: none
Sets the number of stop bits.
Legal values: ``'0_5'``, ``'1'``, ``'1_5'``, ``'2'``
* - ``data-bits``
- ``int``
- .. code-block:: none
Sets the number of data bits.
Legal values: ``5``, ``6``, ``7``, ``8``, ``9``
* - ``pinctrl-0``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
This property is **required**.
* - ``pinctrl-1``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the second state. See pinctrl-0.
* - ``pinctrl-2``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the third state. See pinctrl-0.
* - ``pinctrl-3``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fourth state. See pinctrl-0.
* - ``pinctrl-4``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fifth state. See pinctrl-0.
* - ``pinctrl-names``
- ``string-array``
- .. code-block:: none
Names for the provided states. The number of names needs to match the
number of states.
This property is **required**.
* - ``input-src``
- ``string``
- .. code-block:: none
Connects the UART receive line (USIC DX0 input) to a specific GPIO pin.
The USIC DX0 input is a multiplexer which connects to different GPIO pins.
Refer to the XMC4XXX reference manual for the GPIO pin/mux mappings. DX0G
is the loopback input line.
This property is **required**.
Legal values: ``'DX0A'``, ``'DX0B'``, ``'DX0C'``, ``'DX0D'``, ``'DX0E'``, ``'DX0F'``, ``'DX0G'``
* - ``fifo-start-offset``
- ``int``
- .. code-block:: none
Each USIC0..2 has a fifo that is shared between two channels. For example,
usic0ch0 and usic0ch1 will share the same fifo. This parameter defines an offset
where the tx and rx fifos will start. When sharing the fifo, the user must properly
define the offset based on the configuration of the other channel. The fifo has a
capacity of 64 entries. The tx/rx fifos are created on fifo-xx-size aligned
boundaries.
This property is **required**.
* - ``fifo-tx-size``
- ``int``
- .. code-block:: none
Fifo size used for buffering transmit bytes. A value of 0 implies that
the fifo is not used while transmitting. transmitting. If the UART is used in async mode
then fifo-tx-size should be set to 0.
This property is **required**.
Legal values: ``0``, ``2``, ``4``, ``8``, ``16``, ``32``, ``64``
* - ``fifo-rx-size``
- ``int``
- .. code-block:: none
Fifo size used for buffering received bytes. A value of 0 implies that
the fifo is not used while receiving. If the UART is used in async mode
then fifo-rx-size should be set to 0.
This property is **required**.
Legal values: ``0``, ``2``, ``4``, ``8``, ``16``, ``32``, ``64``
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "infineon,xmc4xxx-uart" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
* - ``zephyr,pm-device-runtime-auto``
- ``boolean``
- .. code-block:: none
Automatically configure the device for runtime power management after the
init function runs.
* - ``zephyr,disabling-power-states``
- ``phandles``
- .. code-block:: none
List of power states that will disable this device power.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
IRQ number and priority to use for interrupt driven UART.
USIC0..2 have their own interrupt range as follows:
USIC0 = [84, 89]
USIC1 = [90, 95]
USIC2 = [96, 101]
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
See :ref:`zephyr:dt-important-props` for more information.
This property is **deprecated**.
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
Optional TX & RX dma specifiers used by async UART.
The dmas are referenced in the UART node using the following syntax:
dmas = <&dma1 1 0 XMC4XXX_SET_CONFIG(10,6)>, <&dma1 2 0 XMC4XXX_SET_CONFIG(11,6)>;
where the first entry is for the TX, and the second for RX.
The parameters in the dma entry are: dma device phandle, dma channel, dma priority (0 is
lowest and 7 is highest), and an opaque entry for the dma line routing parameters set
by the macro XMC4XXX_SET_CONFIG(line, request_source). Use the following steps to properly
select parameters line, request_source:
1. Select a dma device and a free dma channel.
1. Select a free dma line. dma0 device can only connect to lines [0, 7] and
dma1 can connect to lines [8, 11].
2. For a given interrupt, calculate the service request (SR) number. Note the following
simple mapping: in USIC0 interrupt 84->SR0, interrupt 85->SR1, ... etc.
In USIC1, interrupt 90->SR0, 91->SR1, etc.
3. Select request_source from Table "DMA Request Source Selection" in XMC4XXX reference
manual.
For example, say we select interrupt 85 on USIC0, dma0, channel 3, priority 4, and line 7.
The interrupt would map to SR1. From Table "DMA Request Source Selection", request_source
would need to be set to 10 and the dts entry would be:
dma = <&dma0 3 4 XMC4XXX_SET_CONFIG(7,10) ... >;
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Required if the dmas property exists. Should be set to "tx" and "rx"
to match the dmas property.
For example
dma-names = "tx", "rx";
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``zephyr,deferred-init``
- ``boolean``
- .. code-block:: none
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().