:orphan:
.. raw:: html
.. dtcompatible:: adi,max14906-gpio
.. _dtbinding_adi_max14906_gpio:
adi,max14906-gpio (on spi bus)
##############################
Vendor: :ref:`Analog Devices, Inc. `
.. note::
An implementation of a driver matching this compatible is available in
:zephyr_file:`drivers/gpio/gpio_max14906.c`.
Description
***********
.. code-block:: none
ADI MAX14906 quad industrial Input/Output with advanced diagnostics
Properties
**********
Top level properties
====================
These property descriptions apply to "adi,max14906-gpio"
nodes themselves. This page also describes child node
properties in the following sections.
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``#gpio-cells``
- ``int``
- .. code-block:: none
Number of items to expect in a GPIO specifier
This property is **required**.
Constant value: ``2``
* - ``ngpios``
- ``int``
- .. code-block:: none
Number of gpios supported
This property is **required**.
Default value: ``32``
Constant value: ``4``
* - ``drdy-gpios``
- ``phandle-array``
- .. code-block:: none
High-Side Open-Drain Output. READY is passive low when the internal
logic supply is higher than the UVLO threshold, indicating that the
registers have adequate supply voltage.
* - ``fault-gpios``
- ``phandle-array``
- .. code-block:: none
Fault pin indicates when there is Fault state in either FAULT1 or FAULT2
bothe of which are cleaned on read once problem is not persistent.
* - ``sync-gpios``
- ``phandle-array``
- .. code-block:: none
Latch the data so it could be read (partially duplicate CS).
* - ``en-gpios``
- ``phandle-array``
- .. code-block:: none
DOI Enable Pin. Drive the EN pin high to enable the DOI_ outputs.
Drive EN low to disable/three-state all DOI_ outputs.
* - ``crc-en``
- ``boolean``
- .. code-block:: none
Notify driver if crc pin is enabled.
* - ``spi-addr``
- ``int``
- .. code-block:: none
On MAX14906PMB module default address is 0 (A0-LOW, A1-LOW)
Selectable device address, configurable from A0 and A1
This property is **required**.
Legal values: ``0``, ``1``, ``2``, ``3``
* - ``ow-en``
- ``array``
- .. code-block:: none
Default values are from documentation.
Enable or disable open-wire functionality per channel.
- 0 mean disable
- 1 mean enable
channels indentation start from CH0...CH3
Default value: ``[0, 0, 0, 0]``
* - ``vdd-ov-en``
- ``array``
- .. code-block:: none
Default values are from documentation.
VDDOVEN
Enable or disable open-wire functionality per channel.
- 0 mean disable
- 1 mean enable
channels indentation start from CH0...CH3
Default value: ``[0, 0, 0, 0]``
* - ``gdrv-en``
- ``array``
- .. code-block:: none
Default values are from documentation.
GDrvEn - Gate drive enabl disable for power eff
Enable or disable open-wire functionality per channel.
- 0 mean disable
- 1 mean enable
channels indentation start from CH0...CH3
Default value: ``[0, 0, 0, 0]``
* - ``sh-vdd-en``
- ``array``
- .. code-block:: none
Default values are from documentation.
ShVddEN - Short to VDD enable
Enable or disable short to VDD functionality per channel.
- 0 mean disable
- 1 mean enable
channels indentation start from CH0...CH3
Default value: ``[0, 0, 0, 0]``
* - ``fled-set``
- ``boolean``
- .. code-block:: none
Internal fault diagnostics include (if enabled): SafeDemagF_, SHVDD_,
VDDOV_, OWOff_, AboveVDD_, CL_, OVL_, VDDOKFault_.
* - ``sled-set``
- ``boolean``
- .. code-block:: none
Enable status LEDs
* - ``fled-stretch``
- ``int``
- .. code-block:: none
Default values are from documentation.
Set minimum on time for FLEDs in case of fault
0 - Disable minimum fault LED (FLED) on-time
1 - Minimum fault LED (FLED) on-time = 1s (typ)
2 - Minimum fault LED (FLED) on-time = 2s (typ)
3 - Minimum fault LED (FLED) on-time = 3s (typ)
Legal values: ``0``, ``1``, ``2``, ``3``
* - ``ffilter-en``
- ``boolean``
- .. code-block:: none
When the fault LEDs (FLEDs) are controlled internally (FLEDSet = 0), open-
wire and short-to-V DD diagnostics always use filtering and cannot be disabled
by the FFilterEn bit.
* - ``filter-long``
- ``boolean``
- .. code-block:: none
false: To select regular blanking time (4ms, typ) for diagnostic fault bits, OWOff_
and SHVDD_
true: To select long blanking time (8ms, typ) for diagnostic fault bits, OWOff_
and SHVDD_
* - ``flatch-en``
- ``boolean``
- .. code-block:: none
false: Disable latching of diagnostic fault bits in the OvrLdChF, OpnWirChF, and
ShtVDDChF registers
true: Enable latching of diagnostic fault bits in the OvrLdChF, OpnWirChF, and
ShtVDDChF registers
* - ``led-cur-lim``
- ``boolean``
- .. code-block:: none
false: Disable fault LEDs (FLEDs) signaling current limit
true: Enable fault LEDs (FLEDs) signaling current limit
* - ``vdd-on-thr``
- ``boolean``
- .. code-block:: none
Enable higher voltage thresholds for VDD and VDD_ undervoltage monitoring
* - ``synch-wd-en``
- ``boolean``
- .. code-block:: none
The SYNCH watchdog timeout is defined by the WDTo[1:0] bits if the SPI
watchdog is enabled. When WDTo[1:0] = 00 (SPI watchdog disabled), the
SYNCH watchdog timeout is 600ms (typ) if enabled.
* - ``sht-vdd-thr``
- ``int``
- .. code-block:: none
Default values are from documentation.
Set threshold voltage for short-to-V DD detection
0: Set threshold voltage for short-to-VDD detection to 9V (typ)
1: Set threshold voltage for short-to-VDD detection to 10V (typ)
2: Set threshold voltage for short-to-VDD detection to 12V (typ)
3: Set threshold voltage for short-to-VDD detection to 14V (typ)
Legal values: ``0``, ``1``, ``2``, ``3``
* - ``ow-off-cs``
- ``int``
- .. code-block:: none
Default values are from documentation.
Set the pullup current for open-wire and short-to-VDD detection
0: Set open-wire and short-to-VDD detection current to 60μA (typ)
1: Set open-wire and short-to-VDD detection current to 100μA (typ)
2: Set open-wire and short-to-VDD detection current to 300μA (typ)
3: Set open-wire and short-to-VDD detection current to 600μA (typ)
Legal values: ``0``, ``1``, ``2``, ``3``
* - ``wd-to``
- ``int``
- .. code-block:: none
Default values are from documentation.
SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout
0: Disable SPI Watchdog Status and SPI Watchdog Timeout
1: Enable SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout to 200ms (typ)
2: Enable SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout to 600ms (typ)
3: Enable SPI Watchdog Status, set SPI and SYNCH Watchdog Timeout to 1.2s (typ)
Legal values: ``0``, ``1``, ``2``, ``3``
* - ``gpio-controller``
- ``boolean``
- .. code-block:: none
Convey's this node is a GPIO controller
This property is **required**.
* - ``gpio-reserved-ranges``
- ``array``
- .. code-block:: none
If not all the GPIOs at offsets 0...N-1 are usable for ngpios = , then
this property contains an additional set of tuples which specify which GPIOs
are unusable. This property indicates the start and size of the GPIOs
that can't be used.
For example, setting "gpio-reserved-ranges = <3 2>, <10 1>;" means that
GPIO offsets 3, 4, and 10 are not usable, even if ngpios = <18>.
* - ``gpio-line-names``
- ``string-array``
- .. code-block:: none
This is an array of strings defining the names of the GPIO lines
going out of the GPIO controller
* - ``spi-max-frequency``
- ``int``
- .. code-block:: none
Maximum clock frequency of device's SPI interface in Hz
This property is **required**.
* - ``duplex``
- ``int``
- .. code-block:: none
Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
0 SPI_FULL_DUPLEX
2048 SPI_HALF_DUPLEX
Legal values: ``0``, ``2048``
* - ``frame-format``
- ``int``
- .. code-block:: none
Motorola or TI frame format. By default it's always Motorola's,
thus 0 as this is, by far, the most common format.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
0 SPI_FRAME_FORMAT_MOTOROLA
32768 SPI_FRAME_FORMAT_TI
Legal values: ``0``, ``32768``
* - ``spi-cpol``
- ``boolean``
- .. code-block:: none
SPI clock polarity which indicates the clock idle state.
If it is used, the clock idle state is logic high; otherwise, low.
* - ``spi-cpha``
- ``boolean``
- .. code-block:: none
SPI clock phase that indicates on which edge data is sampled.
If it is used, data is sampled on the second edge; otherwise, on the first edge.
* - ``spi-hold-cs``
- ``boolean``
- .. code-block:: none
In some cases, it is necessary for the master to manage SPI chip select
under software control, so that multiple spi transactions can be performed
without releasing it. A typical use case is variable length SPI packets
where the first spi transaction reads the length and the second spi transaction
reads length bytes.
* - ``supply-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
* - ``vin-supply``
- ``phandle``
- .. code-block:: none
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "adi,max14906-gpio" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
See :ref:`zephyr:dt-important-props` for more information.
This property is **deprecated**.
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``power-domains``
- ``phandle-array``
- .. code-block:: none
Power domain specifiers
* - ``power-domain-names``
- ``string-array``
- .. code-block:: none
Provided names of power domain specifiers
* - ``#power-domain-cells``
- ``int``
- .. code-block:: none
Number of cells in power-domains property
* - ``zephyr,deferred-init``
- ``boolean``
- .. code-block:: none
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``zephyr,pm-device-runtime-auto``
- ``boolean``
- .. code-block:: none
Automatically configure the device for runtime power management after the
init function runs.
* - ``zephyr,disabling-power-states``
- ``phandles``
- .. code-block:: none
List of power states that will disable this device power.
Child node properties
=====================
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``gpio-hog``
- ``boolean``
- .. code-block:: none
Conveys this node is a GPIO hog.
This property is **required**.
* - ``gpios``
- ``array``
- .. code-block:: none
This is an array of GPIO specifiers (e.g. pin, flags) to be hogged. The number of array
entries must be an integer multiple of the number of GPIO specifier cells for the parent
GPIO controller.
This property is **required**.
* - ``input``
- ``boolean``
- .. code-block:: none
If this property is set, the GPIO is configured as an input. This property takes
precedence over the output-low and output-high properties.
* - ``output-low``
- ``boolean``
- .. code-block:: none
If this property is set, the GPIO is configured as an output set to logical low. This
property takes precedence over the output-high property.
* - ``output-high``
- ``boolean``
- .. code-block:: none
If this property is set, the GPIO is configured as an output set to logical high.
* - ``line-name``
- ``string``
- .. code-block:: none
Optional GPIO line name.
Specifier cell names
********************
- gpio cells: pin, flags