:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: zephyr,mipi-dbi-spi
.. _dtbinding_zephyr_mipi_dbi_spi:

zephyr,mipi-dbi-spi
###################

Vendor: :ref:`Zephyr-specific binding <dt_vendor_zephyr>`

.. note::

   An implementation of a driver matching this compatible is available in
   :zephyr_file:`drivers/mipi_dbi/mipi_dbi_spi.c`.

Description
***********

These nodes are "mipi-dbi" bus nodes.

.. code-block:: none

   MIPI-DBI Mode C compatible SPI controller. This driver emulates MIPI DBI
   mode C using a SPI controller and GPIO pins

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``spi-dev``
           - ``phandle``
           - .. code-block:: none

                SPI device to use for data transfers with MIPI DBI commands. This SPI
                device should be connected to the MIPI DBI display.



             This property is **required**.

         * - ``dc-gpios``
           - ``phandle-array``
           - .. code-block:: none

                Data/command gpio pin. Required when using 4 wire SPI mode (Mode C1).
                Set to low when sending a command, or high when sending data.



         * - ``reset-gpios``
           - ``phandle-array``
           - .. code-block:: none

                Reset GPIO pin. Set high to reset the display



         * - ``xfr-min-bits``
           - ``int``
           - .. code-block:: none

                On rare types of SPI interfaces, discrete shift registers can be found whose task is to convert the serial SPI bit stream to the parallel MCU interface with clock and bit accuracy. Typically, these are 16 bits wide.
                Use the macros, not the actual enum value. Here is the concordance list (see dt-bindings/mipi_dbi/mipi_dbi.h) 8     MIPI_DBI_SPI_XFR_8BIT 16     MIPI_DBI_SPI_XFR_16BIT


             Default value: ``8``

             Legal values: ``8``, ``16``

         * - ``write-only``
           - ``boolean``
           - .. code-block:: none

                Only writes to display controller, do not perform reads.
                If all controllers are write-only, read functions will be
                optimized out for size.
                It can also be used as an alternative to half duplex when
                only one data line is connected.



         * - ``clock-frequency``
           - ``int``
           - .. code-block:: none

                Clock frequency of the SCL signal of the MBI-DBI peripheral, in Hz



         * - ``pinctrl-0``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the first state. Content is specific to the
                selected pin controller driver implementation.



         * - ``pinctrl-1``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the second state. See pinctrl-0.



         * - ``pinctrl-2``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the third state. See pinctrl-0.



         * - ``pinctrl-3``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fourth state. See pinctrl-0.



         * - ``pinctrl-4``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fifth state. See pinctrl-0.



         * - ``pinctrl-names``
           - ``string-array``
           - .. code-block:: none

                Names for the provided states. The number of names needs to match the
                number of states.





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "zephyr,mipi-dbi-spi" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


             This property is **required**.

             Constant value: ``1``

         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


             This property is **required**.

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`zephyr:dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``power-domains``
           - ``phandle-array``
           - .. code-block:: none

                Power domain specifiers


         * - ``power-domain-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of power domain specifiers


         * - ``#power-domain-cells``
           - ``int``
           - .. code-block:: none

                Number of cells in power-domains property


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().



         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.