:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: regulator-fixed
.. _dtbinding_regulator_fixed:

regulator-fixed
###############

Vendor: :ref:`Generic or vendor-independent <dt_no_vendor>`

.. note::

   An implementation of a driver matching this compatible is available in
   :zephyr_file:`drivers/regulator/regulator_fixed.c`.

Description
***********



.. code-block:: none

   Fixed voltage regulators

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``regulator-name``
           - ``string``
           - .. code-block:: none

                A string used as a descriptive name for regulator outputs


             This property is **required**.

         * - ``enable-gpios``
           - ``phandle-array``
           - .. code-block:: none

                GPIO to use to enable/disable the regulator.

                Unlike the gpio property in the Linux bindings this array must
                provide the GPIO polarity and open-drain status in the phandle
                selector.  The Linux enable-active-high and gpio-open-drain
                properties are not valid for Zephyr devicetree files.



         * - ``regulator-min-microvolt``
           - ``int``
           - .. code-block:: none

                smallest voltage consumers may set


         * - ``regulator-max-microvolt``
           - ``int``
           - .. code-block:: none

                largest voltage consumers may set


         * - ``regulator-always-on``
           - ``boolean``
           - .. code-block:: none

                boolean, regulator should never be disabled


         * - ``regulator-boot-on``
           - ``boolean``
           - .. code-block:: none

                bootloader/firmware enabled regulator.
                It's expected that this regulator was left on by the bootloader.
                If the bootloader didn't leave it on then OS should turn it on
                at boot but shouldn't prevent it from being turned off later.
                This property is intended to only be used for regulators where
                software cannot read the state of the regulator.



         * - ``startup-delay-us``
           - ``int``
           - .. code-block:: none

                Startup time, in microseconds


         * - ``off-on-delay-us``
           - ``int``
           - .. code-block:: none

                Off to on delay time, in microseconds




   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "regulator-fixed" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`zephyr:dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``power-domains``
           - ``phandle-array``
           - .. code-block:: none

                Power domain specifiers


         * - ``power-domain-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of power domain specifiers


         * - ``#power-domain-cells``
           - ``int``
           - .. code-block:: none

                Number of cells in power-domains property


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().



         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.