:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: st,stm32-temp-cal
.. _dtbinding_st_stm32_temp_cal:

st,stm32-temp-cal
#################

Vendor: :ref:`STMicroelectronics N.V. <dt_vendor_st>`

.. note::

   An implementation of a driver matching this compatible is available in
   :zephyr_file:`drivers/sensor/st/stm32_temp/stm32_temp.c`.

Description
***********



.. code-block:: none

   STM32 family TEMP node for production calibrated sensors with two calibration temperatures.

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``ts-cal2-addr``
           - ``int``
           - .. code-block:: none

                Address of TS_CAL2 calibration parameter


             This property is **required**.

         * - ``ts-cal2-temp``
           - ``int``
           - .. code-block:: none

                Temperature at which TS_CAL2 has been measured (TS_CAL2_TEMP)


             This property is **required**.

         * - ``ts-cal1-addr``
           - ``int``
           - .. code-block:: none

                Address of TS_CAL1 calibration parameter


             This property is **required**.

         * - ``ts-cal1-temp``
           - ``int``
           - .. code-block:: none

                Temperature at which TS_CAL1 has been measured (TS_CAL2_TEMP)


             This property is **required**.

         * - ``ts-cal-vrefanalog``
           - ``int``
           - .. code-block:: none

                Analog voltage reference (Vref+) voltage with which
                temperature sensor calibration parameters have been
                measured



             This property is **required**.

         * - ``ts-cal-resolution``
           - ``int``
           - .. code-block:: none

                ADC resolution used for measuring calibration data

                This is usually equal to the ADC's native resolution.

                Most series have a 12-bit ADC, but 14-bit and 16-bit
                also exists on e.g., STM32U5 and STM32H7 (16) series.



             Default value: ``12``

             Legal values: ``12``, ``14``, ``16``

         * - ``friendly-name``
           - ``string``
           - .. code-block:: none

                Human readable string describing the sensor. It can be used to
                distinguish multiple instances of the same model (e.g., lid accelerometer
                vs. base accelerometer in a laptop) to a host operating system.

                This property is defined in the Generic Sensor Property Usages of the HID
                Usage Tables specification
                (https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "st,stm32-temp-cal" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`zephyr:dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`zephyr:dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


             This property is **required**.

         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``power-domains``
           - ``phandle-array``
           - .. code-block:: none

                Power domain specifiers


         * - ``power-domain-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of power domain specifiers


         * - ``#power-domain-cells``
           - ``int``
           - .. code-block:: none

                Number of cells in power-domains property


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().



         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.