:orphan:
.. raw:: html
.. dtcompatible:: renesas,smartbond-uart
.. _dtbinding_renesas_smartbond_uart:
renesas,smartbond-uart
######################
Vendor: :ref:`Renesas Electronics Corporation `
.. note::
An implementation of a driver matching this compatible is available in
:zephyr_file:`drivers/serial/uart_smartbond.c`.
Description
***********
These nodes are "uart" bus nodes.
.. code-block:: none
Renesas SmartBond(tm) UART
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``periph-clock-config``
- ``int``
- .. code-block:: none
Peripheral clock register configuration (COM domain)
This property is **required**.
* - ``current-speed``
- ``int``
- .. code-block:: none
Initial baud rate setting for UART. Only a fixed set of baud
rates are selectable on these devices.
Legal values: ``4800``, ``9600``, ``14400``, ``19200``, ``28800``, ``38400``, ``57600``, ``115200``, ``230400``, ``500000``, ``921600``, ``1000000``, ``2000000``
* - ``hw-flow-control-supported``
- ``boolean``
- .. code-block:: none
Set to indicate RTS/CTS flow control is supported.
* - ``rx-wake-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO configured as wake source
* - ``rx-wake-timeout``
- ``int``
- .. code-block:: none
Time to prevent UART entering sleep mode after receiving data (ms)
* - ``dtr-gpios``
- ``phandle-array``
- .. code-block:: none
DTR pin specification. DTR pin when active tells that the driver that there
is active client on the other side of serial line.
The device driver does not use DTR for hardware flow control.
When device is connected to computer serial converter usually asserts DTR
line when serial port is opened and ready for communication.
This line can be used in Smartbond(tm) driver to detect remote client presence.
If client is not present the device can disable UART, allowing for
power system management to enter more efficient power levels.
* - ``clock-frequency``
- ``int``
- .. code-block:: none
Clock frequency information for UART operation
* - ``hw-flow-control``
- ``boolean``
- .. code-block:: none
Set to enable RTS/CTS flow control at boot time
* - ``parity``
- ``string``
- .. code-block:: none
Configures the parity of the adapter. Enumeration id 0 for none, 1 for odd
and 2 for even parity. Default to none if not specified.
Legal values: ``'none'``, ``'odd'``, ``'even'``
* - ``stop-bits``
- ``string``
- .. code-block:: none
Sets the number of stop bits.
Legal values: ``'0_5'``, ``'1'``, ``'1_5'``, ``'2'``
* - ``data-bits``
- ``int``
- .. code-block:: none
Sets the number of data bits.
Legal values: ``5``, ``6``, ``7``, ``8``, ``9``
* - ``pinctrl-0``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
* - ``pinctrl-1``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the second state. See pinctrl-0.
* - ``pinctrl-2``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the third state. See pinctrl-0.
* - ``pinctrl-3``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fourth state. See pinctrl-0.
* - ``pinctrl-4``
- ``phandles``
- .. code-block:: none
Pin configuration/s for the fifth state. See pinctrl-0.
* - ``pinctrl-names``
- ``string-array``
- .. code-block:: none
Names for the provided states. The number of names needs to match the
number of states.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "renesas,smartbond-uart" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`zephyr:dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`zephyr:dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
See :ref:`zephyr:dt-important-props` for more information.
This property is **deprecated**.
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``power-domains``
- ``phandle-array``
- .. code-block:: none
Power domain specifiers
* - ``power-domain-names``
- ``string-array``
- .. code-block:: none
Provided names of power domain specifiers
* - ``#power-domain-cells``
- ``int``
- .. code-block:: none
Number of cells in power-domains property
* - ``zephyr,deferred-init``
- ``boolean``
- .. code-block:: none
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``zephyr,pm-device-runtime-auto``
- ``boolean``
- .. code-block:: none
Automatically configure the device for runtime power management after the
init function runs.
* - ``zephyr,disabling-power-states``
- ``phandles``
- .. code-block:: none
List of power states that will disable this device power.