:orphan: .. raw:: html .. dtcompatible:: worldsemi,ws2812-gpio .. _dtbinding_worldsemi_ws2812_gpio: worldsemi,ws2812-gpio ##################### Vendor: :ref:`Worldsemi Co., Limited ` .. note:: An implementation of a driver matching this compatible is available in :zephyr_file:`drivers/led_strip/ws2812_gpio.c`. Description *********** .. code-block:: none Worldsemi WS2812 LED strip, GPIO binding Driver bindings for bit-banging a WS2812 or compatible LED strip. The CPU driver uses inline assembly, and isn't available for all boards. The timing is automatically derived from the CPU clock frequency, or can be provided by setting the delay-txx properties in the device tree, or can be manually provided by the Kconfig settings DELAY_Txx. The four delays provided (calculated based on the clock frequency, provided by a dts, or Kconfig file) determine the delays as depicted below. The exact timings of the LED strip data line might vary on the type of LEDs used, consult the data-sheet for the precise timings. 0 code +-------+ +--- | | | | T0H | T0L | | | | ---+ +-----------------+ 1 code +---------------+ +--- | | | | T1H | T1L | | | | ---+ +---------+ Example dts file: / { cpus { cpu@0 { clock-frequency = <64000000>; }; }; rgb_led: ws2812 { compatible = "worldsemi,ws2812-gpio"; chain-length = <1>; color-mapping = ; gpios = <&gpio0 16 0>; }; }; Example dts file: / { chosen { zephyr,led-strip = &rgb_led; }; rgb_led: ws2812 { compatible = "worldsemi,ws2812-gpio"; chain-length = <1>; color-mapping = ; reset-delay = <50>; gpios = <&gpio0 16 0>; delay-t1h = <48>; delay-t1l = <32>; delay-t0h = <16>; delay-t0l = <32>; }; }; Properties ********** .. tabs:: .. group-tab:: Node specific properties Properties not inherited from the base binding file. .. list-table:: :widths: 1 1 4 :header-rows: 1 * - Name - Type - Details * - ``delay-t1h`` - ``int`` - .. code-block:: none Number of NOP assembly operations to create a delay for a 1 bit, high voltage period (default 700 nsec) * - ``delay-t1l`` - ``int`` - .. code-block:: none Number of NOP assembly operations to create a delay for a 1 bit, low voltage period (default 600 nsec) * - ``delay-t0h`` - ``int`` - .. code-block:: none Number of NOP assembly operations to create a delay for a 0 bit, high voltage period (default 350 nsec) * - ``delay-t0l`` - ``int`` - .. code-block:: none Number of NOP assembly operations to create a delay for a 0 bit, low voltage period (default 800 nsec) * - ``gpios`` - ``phandle-array`` - .. code-block:: none GPIO phandle and specifier for the pin connected to the led-strip. Exactly one pin should be given. This property is **required**. * - ``reset-delay`` - ``int`` - .. code-block:: none Minimum delay to wait (in microseconds) to make sure that the strip has latched the signal. If omitted, a default value of 8 microseconds is used. This default is good for the WS2812 controllers. Note that despite the WS2812 datasheet states that a 50 microseconds delay is required, it seems 6 microseconds is enough. The default is set to 8 microseconds just to be safe. Default value: ``8`` * - ``chain-length`` - ``int`` - .. code-block:: none The number of devices in the daisy-chain. This property is **required**. * - ``color-mapping`` - ``array`` - .. code-block:: none Channel to color mapping (or pixel order). For example a GRB channel to color mapping would be color-mapping = ; This property is **required**. .. group-tab:: Deprecated node specific properties Deprecated properties not inherited from the base binding file. (None) .. group-tab:: Base properties Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the "worldsemi,ws2812-gpio" compatible. .. list-table:: :widths: 1 1 4 :header-rows: 1 * - Name - Type - Details * - ``status`` - ``string`` - .. code-block:: none Indicates the operational status of the hardware or other resource that the node represents. In particular: - "okay" means the resource is operational and, for example, can be used by device drivers - "disabled" means the resource is not operational and the system should treat it as if it is not present For details, see "2.3.4 status" in Devicetree Specification v0.4. Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'`` See :ref:`zephyr:dt-important-props` for more information. * - ``compatible`` - ``string-array`` - .. code-block:: none This property is a list of strings that essentially define what type of hardware or other resource this devicetree node represents. Each device driver checks for specific compatible property values to find the devicetree nodes that represent resources that the driver should manage. The recommended format is "vendor,device", The "vendor" part is an abbreviated name of the vendor. The "device" is usually from the datasheet. The compatible property can have multiple values, ordered from most- to least-specific. Having additional values is useful when the device is a specific instance of a more general family, to allow the system to match the most specific driver available. For details, see "2.3.1 compatible" in Devicetree Specification v0.4. This property is **required**. See :ref:`zephyr:dt-important-props` for more information. * - ``reg`` - ``array`` - .. code-block:: none Information used to address the device. The value is specific to the device (i.e. is different depending on the compatible property). The "reg" property is typically a sequence of (address, length) pairs. Each pair is called a "register block". Values are conventionally written in hex. For details, see "2.3.6 reg" in Devicetree Specification v0.4. See :ref:`zephyr:dt-important-props` for more information. * - ``reg-names`` - ``string-array`` - .. code-block:: none Optional names given to each register block in the "reg" property. For example: / { soc { #address-cells = <1>; #size-cells = <1>; uart@1000 { reg = <0x1000 0x2000>, <0x3000 0x4000>; reg-names = "foo", "bar"; }; }; }; The uart@1000 node has two register blocks: - one with base address 0x1000, size 0x2000, and name "foo" - another with base address 0x3000, size 0x4000, and name "bar" * - ``interrupts`` - ``array`` - .. code-block:: none Information about interrupts generated by the device, encoded as an array of one or more interrupt specifiers. The format of the data in this property varies by where the device appears in the interrupt tree. Devices with the same "interrupt-parent" will use the same format in their interrupts properties. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4. See :ref:`zephyr:dt-important-props` for more information. * - ``interrupts-extended`` - ``compound`` - .. code-block:: none Extended interrupt specifier for device, used as an alternative to the "interrupts" property. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4. * - ``interrupt-names`` - ``string-array`` - .. code-block:: none Optional names given to each interrupt generated by a device. The interrupts themselves are defined in either "interrupts" or "interrupts-extended" properties. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4. * - ``interrupt-parent`` - ``phandle`` - .. code-block:: none If present, this refers to the node which handles interrupts generated by this device. For details, see "2.4 Interrupts and Interrupt Mapping" in Devicetree Specification v0.4. * - ``label`` - ``string`` - .. code-block:: none Human readable string describing the device. Use of this property is deprecated except as needed on a case-by-case basis. For details, see "4.1.2 Miscellaneous Properties" in Devicetree Specification v0.4. See :ref:`zephyr:dt-important-props` for more information. * - ``clocks`` - ``phandle-array`` - .. code-block:: none Information about the device's clock providers. In general, this property should follow conventions established in the dt-schema binding: https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml * - ``clock-names`` - ``string-array`` - .. code-block:: none Optional names given to each clock provider in the "clocks" property. * - ``#address-cells`` - ``int`` - .. code-block:: none This property encodes the number of cells used by address fields in "reg" properties in this node's children. For details, see "2.3.5 #address-cells and #size-cells" in Devicetree Specification v0.4. * - ``#size-cells`` - ``int`` - .. code-block:: none This property encodes the number of cells used by size fields in "reg" properties in this node's children. For details, see "2.3.5 #address-cells and #size-cells" in Devicetree Specification v0.4. * - ``dmas`` - ``phandle-array`` - .. code-block:: none DMA channel specifiers relevant to the device. * - ``dma-names`` - ``string-array`` - .. code-block:: none Optional names given to the DMA channel specifiers in the "dmas" property. * - ``io-channels`` - ``phandle-array`` - .. code-block:: none IO channel specifiers relevant to the device. * - ``io-channel-names`` - ``string-array`` - .. code-block:: none Optional names given to the IO channel specifiers in the "io-channels" property. * - ``mboxes`` - ``phandle-array`` - .. code-block:: none Mailbox / IPM channel specifiers relevant to the device. * - ``mbox-names`` - ``string-array`` - .. code-block:: none Optional names given to the mbox specifiers in the "mboxes" property. * - ``power-domains`` - ``phandle-array`` - .. code-block:: none Power domain specifiers relevant to the device. * - ``power-domain-names`` - ``string-array`` - .. code-block:: none Optional names given to the power domain specifiers in the "power-domains" property. * - ``#power-domain-cells`` - ``int`` - .. code-block:: none Number of cells in power-domains property * - ``zephyr,deferred-init`` - ``boolean`` - .. code-block:: none Do not initialize device automatically on boot. Device should be manually initialized using device_init(). * - ``wakeup-source`` - ``boolean`` - .. code-block:: none Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary. * - ``zephyr,pm-device-runtime-auto`` - ``boolean`` - .. code-block:: none Automatically configure the device for runtime power management after the init function runs. * - ``zephyr,disabling-power-states`` - ``phandles`` - .. code-block:: none List of power states that will disable this device power.