atmel,samd5x-dac

Vendor: Atmel Corporation

Note

An implementation of a driver matching this compatible is available in drivers/dac/dac_samd5x.c.

Description

Atmel SAMD5x/E5x family DAC

To enable the DAC peripheral, it must be enabled in the board dts, or in
subsequent overlay file. In addition, each channel must be configured
using the child-binding properties.

&dac0 {
  status = "okay";
  reference = "intref";

  channel_0 {
    oversampling = <0>;
    refresh-period = <1>;
    current-control = <2>;
  };

  channel_1 {
    oversampling = <0>;
    refresh-period = <1>;
    current-control = <2>;
  };
};

Properties

Top level properties

These property descriptions apply to “atmel,samd5x-dac” nodes themselves. This page also describes child node properties in the following sections.

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

atmel,assigned-clocks

phandle-array

 
Assigned-clock information

This property is required.

atmel,assigned-clock-names

string-array

 
Name of each assigned-clock

This property is required.

reference

string

 
Reference voltage source

Legal values: 'vrefau', 'vddana', 'vrefab', 'intref'

differential-mode

boolean

 
Enable differential mode. When enabled, the DAC outputs the difference
between channel 0 and channel 1 on the VOUT0 pin.

#io-channel-cells

int

This property is required.

Constant value: 1

pinctrl-0

phandles

 
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.

pinctrl-1

phandles

 
Pin configuration/s for the second state. See pinctrl-0.

pinctrl-2

phandles

 
Pin configuration/s for the third state. See pinctrl-0.

pinctrl-3

phandles

 
Pin configuration/s for the fourth state. See pinctrl-0.

pinctrl-4

phandles

 
Pin configuration/s for the fifth state. See pinctrl-0.

pinctrl-names

string-array

 
Names for the provided states. The number of names needs to match the
number of states.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “atmel,samd5x-dac” compatible.

Name

Type

Details

reg

array

 
Information used to address the device. The value is specific to
the device (i.e. is different depending on the compatible
property).

The "reg" property is typically a sequence of (address, length) pairs.
Each pair is called a "register block". Values are
conventionally written in hex.

For details, see "2.3.6 reg" in Devicetree Specification v0.4.

This property is required.

See Important properties for more information.

clocks

phandle-array

 
Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:

  https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml

This property is required.

clock-names

string-array

 
Optional names given to each clock provider in the "clocks" property.

This property is required.

status

string

 
Indicates the operational status of the hardware or other
resource that the node represents. In particular:

  - "okay" means the resource is operational and, for example,
    can be used by device drivers
  - "disabled" means the resource is not operational and the system
    should treat it as if it is not present

For details, see "2.3.4 status" in Devicetree Specification v0.4.

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

 
This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.

The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.

The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.

For details, see "2.3.1 compatible" in Devicetree Specification v0.4.

This property is required.

See Important properties for more information.

reg-names

string-array

 
Optional names given to each register block in the "reg" property.
For example:

  / {
       soc {
           #address-cells = <1>;
           #size-cells = <1>;

           uart@1000 {
               reg = <0x1000 0x2000>, <0x3000 0x4000>;
               reg-names = "foo", "bar";
           };
       };
  };

The uart@1000 node has two register blocks:

  - one with base address 0x1000, size 0x2000, and name "foo"
  - another with base address 0x3000, size 0x4000, and name "bar"

interrupts

array

 
Information about interrupts generated by the device, encoded as an array
of one or more interrupt specifiers. The format of the data in this property
varies by where the device appears in the interrupt tree. Devices with the same
"interrupt-parent" will use the same format in their interrupts properties.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

See Important properties for more information.

interrupts-extended

compound

 
Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

interrupt-names

string-array

 
Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

interrupt-parent

phandle

 
If present, this refers to the node which handles interrupts generated
by this device.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

label

string

 
Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.

For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.

See Important properties for more information.

#address-cells

int

 
This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.

For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.

#size-cells

int

 
This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.

For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.

dmas

phandle-array

 
DMA channel specifiers relevant to the device.

dma-names

string-array

 
Optional names given to the DMA channel specifiers in the "dmas" property.

io-channels

phandle-array

 
IO channel specifiers relevant to the device.

io-channel-names

string-array

 
Optional names given to the IO channel specifiers in the "io-channels" property.

mboxes

phandle-array

 
Mailbox / IPM channel specifiers relevant to the device.

mbox-names

string-array

 
Optional names given to the mbox specifiers in the "mboxes" property.

power-domains

phandle-array

 
Power domain specifiers relevant to the device.

power-domain-names

string-array

 
Optional names given to the power domain specifiers in the "power-domains" property.

#power-domain-cells

int

 
Number of cells in power-domains property

zephyr,deferred-init

boolean

 
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().

wakeup-source

boolean

 
Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

zephyr,pm-device-runtime-auto

boolean

 
Automatically configure the device for runtime power management after the
init function runs.

zephyr,disabling-power-states

phandles

 
List of power states that will disable this device power.

Child node properties

Name

Type

Details

oversampling

string

 
This field defines the oversampling ratio/interpolation depth:
- 0: 1x oversampling (no interpolation)
- 1: 2x oversampling
- 2: 4x oversampling
- 3: 8x oversampling
- 4: 16x oversampling
- 5: 32x oversampling
Higher oversampling ratios provide better noise reduction but
reduce the maximum update rate.

Legal values: 'OSR_1', 'OSR_2', 'OSR_4', 'OSR_8', 'OSR_16', 'OSR_32'

refresh-period

int

 
Defines the refresh period for the DAC output. Only work when the
input data is not interpolated, i.e. the oversampling rate is zero.
- 0: Refresh mode disabled
- 1-15: Refresh period = REFRESH * 30µs

run-in-standby

boolean

 
When enabled, the DAC channel continues to operate in standby mode.

current-control

string

 
Select the output buffer current according to data rate, power
consumption can be reduced by controlling the output buffer
current, according to conversion rate.
- 0: GCLK_DAC ≤ 1.2MHz (100kSPS)
- 1: 1.2MHz < GCLK_DAC ≤ 6MHz (500kSPS)
- 2: 6MHz < GCLK_DAC ≤ 12MHz (1MSPS)

Legal values: 'CC100K', 'CC1M', 'CC12M'