ftdi,ft800 (on spi bus)

Vendor: Future Technology Devices International Ltd.

Note

An implementation of a driver matching this compatible is available in drivers/misc/ft8xx/ft8xx.c.

Description

FTDI FT800 graphic controller

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

irq-gpios

phandle-array

 
Optional IRQ line of FT800 controller

pclk

int

 
The value to divide the main clock by for PCLK. If the
typical main clock was 48MHz and this value is 5, the PCLK
will be 9.6 MHz. Must be positive value to enable the screen

This property is required.

pclk-pol

int

 
Polarity of PCLK. If it is set to zero, PCLK polarity is on
the rising edge. If it is set to one, PCLK polarity is on
the falling edge.

This property is required.

cspread

int

 
Controls the transition of RGB signals with PCLK active clock
edge. When set to 0, R[7:2],G[7:2] and B[7:2] signals change
following the active edge of PCLK. When set to 1, R[7:2]
changes a PCLK clock early and B[7:2] a PCLK clock later,
which helps reduce the system noise.

This property is required.

swizzle

int

 
Controls the arrangement of output RGB pins, which may help
support different LCD panel. Please check FT800 Programmers
Guide for details.

This property is required.

vsize

int

 
Number of visible lines of pixels in one frame

This property is required.

voffset

int

 
Number of invisible lines at the beginning of a new frame

This property is required.

vcycle

int

 
Number of all lines in a frame. It includes all visible and
invisible lines at the beginning and at the end of a frame.

This property is required.

vsync0

int

 
Number of lines for the high state of signal VSYNC at
the start of new frame.

This property is required.

vsync1

int

 
Number of lines for signal VSYNC toggle takes at the start
of new frame.

This property is required.

hsize

int

 
Number of PCLK cycles per visible part of horizontal line

This property is required.

hoffset

int

 
Number of PCLK cycles before pixels are scanned out for
given line

This property is required.

hcycle

int

 
Number of total PCLK cycles per horizontal line scan.

This property is required.

hsync0

int

 
Number of PCLK cycles of HSYNC high state during start of line

This property is required.

hsync1

int

 
Number of PCLK cycles for HSYNC toggle during start of line.

This property is required.

spi-max-frequency

int

 
Maximum clock frequency of device's SPI interface in Hz

This property is required.

duplex

int

 
Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0    SPI_FULL_DUPLEX
  2048 SPI_HALF_DUPLEX

Legal values: 0, 2048

frame-format

int

 
Motorola or TI frame format. By default it's always Motorola's,
thus 0 as this is, by far, the most common format.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0     SPI_FRAME_FORMAT_MOTOROLA
  32768 SPI_FRAME_FORMAT_TI

Legal values: 0, 32768

spi-cpol

boolean

 
SPI clock polarity which indicates the clock idle state.
If it is used, the clock idle state is logic high; otherwise, low.

spi-cpha

boolean

 
SPI clock phase that indicates on which edge data is sampled.
If it is used, data is sampled on the second edge; otherwise, on the first edge.

spi-hold-cs

boolean

 
In some cases, it is necessary for the master to manage SPI chip select
under software control, so that multiple spi transactions can be performed
without releasing it. A typical use case is variable length SPI packets
where the first spi transaction reads the length and the second spi transaction
reads length bytes.

supply-gpios

phandle-array

 
GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

 
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ftdi,ft800” compatible.

Name

Type

Details

reg

array

 
Information used to address the device. The value is specific to
the device (i.e. is different depending on the compatible
property).

The "reg" property is typically a sequence of (address, length) pairs.
Each pair is called a "register block". Values are
conventionally written in hex.

For details, see "2.3.6 reg" in Devicetree Specification v0.4.

This property is required.

See Important properties for more information.

status

string

 
Indicates the operational status of the hardware or other
resource that the node represents. In particular:

  - "okay" means the resource is operational and, for example,
    can be used by device drivers
  - "disabled" means the resource is not operational and the system
    should treat it as if it is not present

For details, see "2.3.4 status" in Devicetree Specification v0.4.

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

 
This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.

The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.

The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.

For details, see "2.3.1 compatible" in Devicetree Specification v0.4.

This property is required.

See Important properties for more information.

reg-names

string-array

 
Optional names given to each register block in the "reg" property.
For example:

  / {
       soc {
           #address-cells = <1>;
           #size-cells = <1>;

           uart@1000 {
               reg = <0x1000 0x2000>, <0x3000 0x4000>;
               reg-names = "foo", "bar";
           };
       };
  };

The uart@1000 node has two register blocks:

  - one with base address 0x1000, size 0x2000, and name "foo"
  - another with base address 0x3000, size 0x4000, and name "bar"

interrupts

array

 
Information about interrupts generated by the device, encoded as an array
of one or more interrupt specifiers. The format of the data in this property
varies by where the device appears in the interrupt tree. Devices with the same
"interrupt-parent" will use the same format in their interrupts properties.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

See Important properties for more information.

interrupts-extended

compound

 
Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

interrupt-names

string-array

 
Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

interrupt-parent

phandle

 
If present, this refers to the node which handles interrupts generated
by this device.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

label

string

 
Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.

For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.

See Important properties for more information.

clocks

phandle-array

 
Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:

  https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml

clock-names

string-array

 
Optional names given to each clock provider in the "clocks" property.

#address-cells

int

 
This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.

For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.

#size-cells

int

 
This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.

For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.

dmas

phandle-array

 
DMA channel specifiers relevant to the device.

dma-names

string-array

 
Optional names given to the DMA channel specifiers in the "dmas" property.

io-channels

phandle-array

 
IO channel specifiers relevant to the device.

io-channel-names

string-array

 
Optional names given to the IO channel specifiers in the "io-channels" property.

mboxes

phandle-array

 
Mailbox / IPM channel specifiers relevant to the device.

mbox-names

string-array

 
Optional names given to the mbox specifiers in the "mboxes" property.

power-domains

phandle-array

 
Power domain specifiers relevant to the device.

power-domain-names

string-array

 
Optional names given to the power domain specifiers in the "power-domains" property.

#power-domain-cells

int

 
Number of cells in power-domains property

zephyr,deferred-init

boolean

 
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().

wakeup-source

boolean

 
Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

zephyr,pm-device-runtime-auto

boolean

 
Automatically configure the device for runtime power management after the
init function runs.

zephyr,disabling-power-states

phandles

 
List of power states that will disable this device power.