atmel,sam-gmac

Vendor: Atmel Corporation

Note

An implementation of a driver matching this compatible is available in drivers/ethernet/eth_sam_gmac.c.

Description

Atmel SAM-family GMAC Ethernet

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

phy-handle

phandle

 
Specifies a reference to a node representing a PHY device.

This property is required.

num-queues

int

 
Number of hardware TX and RX queues.

This property is required.

max-frame-size

int

 
Maximum ethernet frame size.  The current ethernet frame sizes
supported by hardware are 1518, 1536 and 10240 (jumbo frames).  This
means that normally gmac will reject any frame above max-frame-size
value.  The default value is 1518, which represents an usual
IEEE 802.3 ethernet frame:

  Ethernet Frame [ 14 MAC HEADER | 1500 MTU | 4 FCS ] = 1518 bytes

When using value 1536 it is possible extend ethernet MAC HEADER up
to 32 bytes.  The hardware have support to jumbo frames and it can be
enabled by selecting the value 10240.

Default value: 1518

max-speed

int

 
This specifies maximum speed in Mbit/s supported by the device.  The
gmac driver supports 10Mbit/s and 100Mbit/s.  Using 100, as default
value, enables driver to configure 10 and 100Mbit/s speeds.

Default value: 100

mac-eeprom

phandle

 
phandle to I2C eeprom device node.

phy-connection-type

string

 
Specifies the interface connection type between ethernet MAC and PHY.

Default value: rmii

Legal values: 'mii', 'rmii', 'gmii', 'rgmii'

local-mac-address

uint8-array

 
Specifies the MAC address that was assigned to the network device

zephyr,random-mac-address

boolean

 
Use a random MAC address generated when the driver is initialized.
Note that using this choice and rebooting a board may leave stale
MAC address in peers' ARP caches and lead to issues and delays in
communication.  (Use "ip neigh flush all" on Linux peers to clear
ARP cache.)

It is driver specific how the OUI octets are handled.

If set we ignore any setting of the local-mac-address property.

pinctrl-0

phandles

 
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.

pinctrl-1

phandles

 
Pin configuration/s for the second state. See pinctrl-0.

pinctrl-2

phandles

 
Pin configuration/s for the third state. See pinctrl-0.

pinctrl-3

phandles

 
Pin configuration/s for the fourth state. See pinctrl-0.

pinctrl-4

phandles

 
Pin configuration/s for the fifth state. See pinctrl-0.

pinctrl-names

string-array

 
Names for the provided states. The number of names needs to match the
number of states.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “atmel,sam-gmac” compatible.

Name

Type

Details

clocks

phandle-array

 
Clock gate information

This property is required.

reg

array

 
register space

This property is required.

See Important properties for more information.

status

string

 
indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

 
compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

 
name of each register space

interrupts

array

 
interrupts for device

See Important properties for more information.

interrupts-extended

compound

 
extended interrupt specifier for device

interrupt-names

string-array

 
name of each interrupt

interrupt-parent

phandle

 
phandle to interrupt controller node

label

string

 
Human readable string describing the device (used as device_get_binding() argument)

See Important properties for more information.

This property is deprecated.

clock-names

string-array

 
name of each clock

#address-cells

int

 
number of address cells in reg property

#size-cells

int

 
number of size cells in reg property

dmas

phandle-array

 
DMA channels specifiers

dma-names

string-array

 
Provided names of DMA channel specifiers

io-channels

phandle-array

 
IO channels specifiers

io-channel-names

string-array

 
Provided names of IO channel specifiers

mboxes

phandle-array

 
mailbox / IPM channels specifiers

mbox-names

string-array

 
Provided names of mailbox / IPM channel specifiers

power-domains

phandle-array

 
Power domain specifiers

power-domain-names

string-array

 
Provided names of power domain specifiers

#power-domain-cells

int

 
Number of cells in power-domains property

zephyr,deferred-init

boolean

 
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().

wakeup-source

boolean

 
Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

zephyr,pm-device-runtime-auto

boolean

 
Automatically configure the device for runtime power management after the
init function runs.

zephyr,disabling-power-states

phandles

 
List of power states that will disable this device power.