onnn,lc709203f (on i2c bus)

Vendor: ON Semiconductor Corp.

Note

An implementation of a driver matching this compatible is available in drivers/fuel_gauge/lc709203f/lc709203f.c.

Description

ON Semiconductor LC709203F fuel gauge. For more info visit
https://www.onsemi.com/products/power-management/battery-management/battery-fuel-gauges/LC709204F

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

initial-rsoc

boolean

The LSI can be forced to initialize RSOC by sending the he Initial RSOC Command.
The LSI initializes RSOC by the measured voltage at that time when the Initial
RSOC command is written

apa

string

Adjustment Pack Application: Value for a battery type to improve the RSOC precision.
Typical values are provided and should be selected approximately.

This property is required.

Legal values: '100mAh', '200mAh', '500mAh', '1000mAh', '2000mAh', '3000mAh'

battery-profile

int

The LSI contains a data file comprised of two battery profiles.
This register is used to select the battery profile to be used.
Register Number of the Parameter (0x1A) contains identity of the data file.
The Data file is loaded during final test depending on the part number ordered.
To decide which battery-profile should be used please refer to the LC709203F data sheet.

Legal values: 0, 1

thermistor

boolean

Specifies if the device is used with a thermistor or not.

thermistor-b-value

int

Sets B-constant of the thermistor to be measured. Refer to
the specification sheet of the thermistor for the set value to used.
The default is set to 0x0D34 which is the initial value of the IC.
Note: This value will only be set if a thermistor is used.

Default value: 3380

apt

int

This is used to compensate for the delay of the thermistor
measurement caused by a capacitor across the thermistor.
The default value has been found to meet most of circuits
where a capacitor is not put. For details please refer to the
LC709203F data sheet.
Note: This value will only be set if a thermistor is used.

Default value: 30

thermistor-mode

int

This selects the Thermistor mode.
Thermistor mode (0x1): The LSI measures the attached thermistor and
loads the temperature into the Cell Temperature register.
I2C mode (0x0): the temperature is provided by the host processor.
The default is set to 0x1, because if a thermistor is used, the
thermistor mode should be selected.
Note: This value will only be necessary if a thermistor is used,
otherwise the initial value of the IC is 0x0 and setting is not necessary.

Default value: 1

Legal values: 0, 1

supply-gpios

phandle-array

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “onnn,lc709203f” compatible.

Name

Type

Details

reg

array

device address on i2c bus

This property is required.

See Important properties for more information.

status

string

Indicates the operational status of the hardware or other
resource that the node represents. In particular:

  - "okay" means the resource is operational and, for example,
    can be used by device drivers
  - "disabled" means the resource is not operational and the system
    should treat it as if it is not present

For details, see "2.3.4 status" in Devicetree Specification v0.4.

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.

The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.

The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.

For details, see "2.3.1 compatible" in Devicetree Specification v0.4.

This property is required.

See Important properties for more information.

reg-names

string-array

Optional names given to each register block in the "reg" property.
For example:

  / {
       soc {
           #address-cells = <1>;
           #size-cells = <1>;

           uart@1000 {
               reg = <0x1000 0x2000>, <0x3000 0x4000>;
               reg-names = "foo", "bar";
           };
       };
  };

The uart@1000 node has two register blocks:

  - one with base address 0x1000, size 0x2000, and name "foo"
  - another with base address 0x3000, size 0x4000, and name "bar"

interrupts

array

Information about interrupts generated by the device, encoded as an array
of one or more interrupt specifiers. The format of the data in this property
varies by where the device appears in the interrupt tree. Devices with the same
"interrupt-parent" will use the same format in their interrupts properties.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

See Important properties for more information.

interrupts-extended

compound

Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

interrupt-names

string-array

Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

interrupt-parent

phandle

If present, this refers to the node which handles interrupts generated
by this device.

For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.

label

string

Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.

For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.

See Important properties for more information.

clocks

phandle-array

Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:

  https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml

clock-names

string-array

Optional names given to each clock provider in the "clocks" property.

#address-cells

int

This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.

For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.

#size-cells

int

This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.

For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.

dmas

phandle-array

DMA channel specifiers relevant to the device.

dma-names

string-array

Optional names given to the DMA channel specifiers in the "dmas" property.

io-channels

phandle-array

IO channel specifiers relevant to the device.

io-channel-names

string-array

Optional names given to the IO channel specifiers in the "io-channels" property.

mboxes

phandle-array

Mailbox / IPM channel specifiers relevant to the device.

mbox-names

string-array

Optional names given to the mbox specifiers in the "mboxes" property.

power-domains

phandle-array

Power domain specifiers relevant to the device.

power-domain-names

string-array

Optional names given to the power domain specifiers in the "power-domains" property.

#power-domain-cells

int

Number of cells in power-domains property

zephyr,deferred-init

boolean

Do not initialize device automatically on boot. Device should be manually
initialized using device_init().

wakeup-source

boolean

Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

zephyr,pm-device-runtime-auto

boolean

Automatically configure the device for runtime power management after the
init function runs.

zephyr,disabling-power-states

phandles

List of power states that will disable this device power.