adafruit-feather-header

Vendor: Generic or vendor-independent

Description

GPIO pins exposed on Adafruit Feather headers.

The Feather layout provides two headers, one each along
opposite edges of the board.
Proceeding counter-clockwise:
* A 16-pin header.  12 pins on this header are exposed
  by this binding.
* A 12-pin header.  9 pins on this header are exposed
  by this binding.

This binding provides a nexus mapping for 21 pins where parent pins 0
through 5 correspond to A0 through A5, and parent pins 6 through 20
correspond as depicted below:

    - RESET
    - 3V3
    - 3V3
    - GND
    0 A0                     - VBAT
    1 A1                     - EN
    2 A2                     - VBUS
    3 A3                     D13  20
    4 A4                     D12  19
    5 A5                     D11  18
    6 SCK                    D10  17
    7 MOSI                   D9   16
    8 MISO                   D6   15
    9 RX                     D5   14
   10 TX                     SCL  13
   11 D4                     SDA  12

Properties

Node specific properties

Properties not inherited from the base binding file.

Name	Type	Details
gpio-map	compound	This property is required.
gpio-map-mask	compound
gpio-map-pass-thru	compound
#gpio-cells	int	Number of items to expect in a GPIO specifier This property is required.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “adafruit-feather-header” compatible.

Name	Type	Details
status	string	indicates the operational status of a device Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss' See Important properties for more information.
compatible	string-array	compatible strings This property is required. See Important properties for more information.
reg	array	register space See Important properties for more information.
reg-names	string-array	name of each register space
interrupts	array	interrupts for device See Important properties for more information.
interrupts-extended	compound	extended interrupt specifier for device
interrupt-names	string-array	name of each interrupt
interrupt-parent	phandle	phandle to interrupt controller node
label	string	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
clocks	phandle-array	Clock gate information
clock-names	string-array	name of each clock
#address-cells	int	number of address cells in reg property
#size-cells	int	number of size cells in reg property
dmas	phandle-array	DMA channels specifiers
dma-names	string-array	Provided names of DMA channel specifiers
io-channels	phandle-array	IO channels specifiers
io-channel-names	string-array	Provided names of IO channel specifiers
mboxes	phandle-array	mailbox / IPM channels specifiers
mbox-names	string-array	Provided names of mailbox / IPM channel specifiers
power-domains	phandle-array	Power domain specifiers
power-domain-names	string-array	Provided names of power domain specifiers
#power-domain-cells	int	Number of cells in power-domains property
zephyr,deferred-init	boolean	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
wakeup-source	boolean	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
zephyr,pm-device-runtime-auto	boolean	Automatically configure the device for runtime power management after the init function runs.
zephyr,disabling-power-states	phandles	List of power states that will disable this device power.