ite,it51xxx-i2c
Vendor: ITE Tech. Inc.
Note
An implementation of a driver matching this compatible is available in drivers/i2c/i2c_ite_it51xxx.c.
Description
These nodes are “i2c” bus nodes.
ITE it51xxx I2C
Properties
Node specific properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
This property is required. |
|
|
Names for the provided states. The number of names needs to match the
number of states.
This property is required. |
|
|
The SCL pin for the selected port.
This property is required. |
|
|
The SDA pin for the selected port.
This property is required. |
|
|
Maximum time allowed for an I2C transfer.
Default value: |
|
|
Ordinal identifying the port 0 = SMB_CHANNEL_A, 1 = SMB_CHANNEL_B, 2 = SMB_CHANNEL_C, 3 = SMB_CHANNEL_D, 4 = SMB_CHANNEL_E, 5 = SMB_CHANNEL_F, 6 = SMB_CHANNEL_G, 7 = SMB_CHANNEL_H, 8 = SMB_CHANNEL_I,
This property is required. Legal values: |
|
|
The default setting is as described below
1 = SMB_SWITCH_INTERFACE0: Switch to interface0 SMCLK0/SMDAT0
2 = SMB_SWITCH_INTERFACE1: Switch to interface1 SMCLK1/SMDAT1
3 = SMB_SWITCH_INTERFACE2: Switch to interface2 SMCLK2/SMDAT2
4 = SMB_SWITCH_INTERFACE3: Switch to interface3 SMCLK3/SMDAT3
5 = SMB_SWITCH_INTERFACE4: Switch to interface4 SMCLK4/SMDAT4
6 = SMB_SWITCH_INTERFACE5: Switch to interface5 SMCLK5/SMDAT5
7 = SMB_SWITCH_INTERFACE6: Switch to interface6 SMCLK6/SMDAT6
8 = SMB_SWITCH_INTERFACE7: Switch to interface7 SMCLK7/SMDAT7
9 = SMB_SWITCH_INTERFACE8: Switch to interface8 SMCLK8/SMDAT8
10 = SMB_SWITCH_INTERFACE9: Switch to interface9 SMCLK9/SMDAT9
11 = SMB_SWITCH_INTERFACE10: Switch to interface10 SMCLK10/SMDAT10
12 = SMB_SWITCH_INTERFACE11: Switch to interface11 SMCLK11/SMDAT11
13 = SMB_SWITCH_INTERFACE12: Switch to interface12 SMCLK12/SMDAT12
The following is an example of the 'channel-switch-sel' property
being swapped between node &i2c0 and &i2c2 in the application:
Note: The property of 'port-num' cannot be changed in the
application.
If the property of 'channel-switch-sel' is changed, the pinctrl
setting and recovery pin in &i2c0 and &i2c2 nodes must also be
modified accordingly.
Valid example(Host):
Channel A switches to interface2:
&i2c0 {
status = "okay";
pinctrl-0 = <&i2c2_clk_gpf6_default
&i2c2_data_gpf7_default>;
pinctrl-names = "default";
scl-gpios = <&gpiof 6 0>;
sda-gpios = <&gpiof 7 0>;
channel-switch-sel = <SMB_SWITCH_INTERFACE2>;
};
Channel C switches to interface0:
&i2c2 {
status = "okay";
pinctrl-0 = <&i2c0_clk_gpf2_default
&i2c0_data_gpf3_default>;
pinctrl-names = "default";
scl-gpios = <&gpiof 2 0>;
sda-gpios = <&gpiof 3 0>;
channel-switch-sel = <SMB_SWITCH_INTERFACE0>;
};
Invalid example(Host):
Channel A switches to interface2:
&i2c0 {
status = "okay";
pinctrl-0 = <&i2c2_clk_gpf6_default
&i2c2_data_gpf7_default>;
pinctrl-names = "default";
scl-gpios = <&gpiof 6 0>;
sda-gpios = <&gpiof 7 0>;
channel-switch-sel = <SMB_SWITCH_INTERFACE2>;
};
Channel C maintains the original configuration:
&i2c2 {
status = "okay";
pinctrl-0 = <&i2c2_clk_gpf6_default
&i2c2_data_gpf7_default>;
pinctrl-names = "default";
};
Valid example(Target):
Channel A switches to interface5:
&i2c0 {
status = "okay";
pinctrl-0 = <&i2c5_clk_gpa4_default
&i2c5_data_gpa5_default>;
pinctrl-names = "default";
scl-gpios = <&gpioa 4 0>;
sda-gpios = <&gpioa 5 0>;
channel-switch-sel = <SMB_SWITCH_INTERFACE5>;
target-enable;
i2c0_target: target@52 {
compatible = "ite,target-i2c";
reg = <0x52>;
};
};
This property is required. Legal values: |
|
|
This option is used when the I2C target is enabled. It is
necessary to prevent the target port from being configured
with I2C host related initialization.
|
|
|
Only supports write or read mode and the maximum buffer size
is 256 bytes. Support dedicated FIFO mode 16 bytes.
|
|
|
This option is used to support non-FIFO write to shared FIFO
read mode. The maximum supported shared FIFO is 256 bytes.
|
|
|
The I2C controller supports two 32-bytes FIFOs,
FIFO1 supports I2C port 0. FIFO2 only supports one port among
1~8. The default is I2C port 1.
|
|
|
This property is enabled when selecting the push-pull GPIO output
type to drive the I2C recovery. The default is open-drain.
|
|
|
Initial clock frequency in Hz
|
|
|
Size of the submission queue for blocking requests
Default value: |
|
|
Size of the completion queue for blocking requests
Default value: |
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
Base properties
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “ite,it51xxx-i2c” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Information used to address the device. The value is specific to
the device (i.e. is different depending on the compatible
property).
The "reg" property is typically a sequence of (address, length) pairs.
Each pair is called a "register block". Values are
conventionally written in hex.
For details, see "2.3.6 reg" in Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
Information about interrupts generated by the device, encoded as an array
of one or more interrupt specifiers. The format of the data in this property
varies by where the device appears in the interrupt tree. Devices with the same
"interrupt-parent" will use the same format in their interrupts properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
This property is required. Constant value: |
|
|
This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
This property is required. |
|
|
Indicates the operational status of the hardware or other
resource that the node represents. In particular:
- "okay" means the resource is operational and, for example,
can be used by device drivers
- "disabled" means the resource is not operational and the system
should treat it as if it is not present
For details, see "2.3.4 status" in Devicetree Specification v0.4.
Legal values: See Important properties for more information. |
|
|
This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.
The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.
The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.
For details, see "2.3.1 compatible" in Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
Optional names given to each register block in the "reg" property.
For example:
/ {
soc {
#address-cells = <1>;
#size-cells = <1>;
uart@1000 {
reg = <0x1000 0x2000>, <0x3000 0x4000>;
reg-names = "foo", "bar";
};
};
};
The uart@1000 node has two register blocks:
- one with base address 0x1000, size 0x2000, and name "foo"
- another with base address 0x3000, size 0x4000, and name "bar"
|
|
|
Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
If present, this refers to the node which handles interrupts generated
by this device.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.
For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.
See Important properties for more information. |
|
|
Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:
https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml
|
|
|
Optional names given to each clock provider in the "clocks" property.
|
|
|
DMA channel specifiers relevant to the device.
|
|
|
Optional names given to the DMA channel specifiers in the "dmas" property.
|
|
|
IO channel specifiers relevant to the device.
|
|
|
Optional names given to the IO channel specifiers in the "io-channels" property.
|
|
|
Mailbox / IPM channel specifiers relevant to the device.
|
|
|
Optional names given to the mbox specifiers in the "mboxes" property.
|
|
|
Power domain specifiers relevant to the device.
|
|
|
Optional names given to the power domain specifiers in the "power-domains" property.
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|