nordic,nrf-twi

Vendor: Nordic Semiconductor

Description

These nodes are “i2c” bus nodes.

Nordic nRF family TWI (TWI master).

This binding can be used for nodes which can represent TWI
peripherals. When a single SoC peripheral ID corresponds to multiple
I2C peripherals (like TWI or TWIM), the corresponding devicetree
nodes must be set up to select TWI before use.

To select TWI, set the node's "compatible" to "nordic,nrf-twi" and
its "status" to "okay", e.g. using an overlay file like this:

    /* This is for TWI0 -- change to "i2c1" for TWI1. */
    &i2c0 {
            compatible = "nordic,nrf-twi";
            status = "okay";
            /* other property settings can go here */
    };

You can use either of these options to check TWI availability on
your SoC:

    1. Check the peripheral Instantiation table in the Memory
       section of your SoC's Product Specification document.
       A "TWI0" instance in the table means "i2c0" in the devicetree
       can be used with this binding, and similarly for "TWI1".

    2. Open your SoC's .dtsi file and look for a node definition that
       documents TWI support, like this:

           i2c0: i2c@40003000 {
                   /*
                    * This i2c node can be TWI, [...].
                    */
                   ...
           };

 If your SoC only has TWIM and TWIS I2C peripherals, you cannot use
 this binding. See the "nordic,nrf-twim" binding instead.

Properties

Node specific properties

Properties not inherited from the base binding file.

Name	Type	Details
pinctrl-0	phandles	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation. This property is required.
pinctrl-names	string-array	Names for the provided states. The number of names needs to match the number of states. This property is required.
easydma-maxcnt-bits	int	Maximum number of bits available in the EasyDMA MAXCNT register. This property must be set at SoC level DTS files. This property is required.
clock-frequency	int	Initial clock frequency in Hz
sq-size	int	Size of the submission queue for blocking requests Default value: 4
cq-size	int	Size of the completion queue for blocking requests Default value: 4
pinctrl-1	phandles	Pin configuration/s for the second state. See pinctrl-0.
pinctrl-2	phandles	Pin configuration/s for the third state. See pinctrl-0.
pinctrl-3	phandles	Pin configuration/s for the fourth state. See pinctrl-0.
pinctrl-4	phandles	Pin configuration/s for the fifth state. See pinctrl-0.
nordic,clockpin-enable	array	List of signals that require CLOCKPIN setting enablement.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nordic,nrf-twi” compatible.

Name	Type	Details
reg	array	register space This property is required. See Important properties for more information.
interrupts	array	interrupts for device This property is required. See Important properties for more information.
#address-cells	int	number of address cells in reg property This property is required. Constant value: 1
#size-cells	int	number of size cells in reg property This property is required.
status	string	indicates the operational status of a device Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss' See Important properties for more information.
compatible	string-array	compatible strings This property is required. See Important properties for more information.
reg-names	string-array	name of each register space
interrupts-extended	compound	extended interrupt specifier for device
interrupt-names	string-array	name of each interrupt
interrupt-parent	phandle	phandle to interrupt controller node
label	string	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
clocks	phandle-array	Clock gate information
clock-names	string-array	name of each clock
dmas	phandle-array	DMA channels specifiers
dma-names	string-array	Provided names of DMA channel specifiers
io-channels	phandle-array	IO channels specifiers
io-channel-names	string-array	Provided names of IO channel specifiers
mboxes	phandle-array	mailbox / IPM channels specifiers
mbox-names	string-array	Provided names of mailbox / IPM channel specifiers
power-domains	phandle-array	Power domain specifiers
power-domain-names	string-array	Provided names of power domain specifiers
#power-domain-cells	int	Number of cells in power-domains property
zephyr,deferred-init	boolean	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
wakeup-source	boolean	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
zephyr,pm-device-runtime-auto	boolean	Automatically configure the device for runtime power management after the init function runs.
zephyr,disabling-power-states	phandles	List of power states that will disable this device power.