st,stm32h7-fmc
Vendor: STMicroelectronics N.V.
Description
STM32 Flexible Memory Controller (FMC).
The FMC allows to interface with static-memory mapped external devices such as
SRAM, NOR Flash, NAND Flash, SDRAM...
All external memories share the addresses, data and control signals with the
controller. Each external device is accessed by means of a unique chip select.
The FMC performs only one access at a time to an external device.
The flexible memory controller includes three memory controllers:
- NOR/PSRAM memory controller
- NAND memory controller (some devices also support PC Card)
- Synchronous DRAM (SDRAM/Mobile LPSDR SDRAM) controller
Each memory controller is defined below the FMC DeviceTree node and is managed
by a separate Zephyr device. However, because signals are shared the FMC
device handles the signals and the peripheral clocks. FMC can be enabled
in your board DeviceTree file like this:
&fmc {
status = "okay";
pinctrl-0 = <&fmc_nbl0_pe0 &fmc_nbl1_pe1 &fmc_nbl2_pi4...>;
};
Properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.
This property is required. |
|
|
Pin configuration/s for the second state. See pinctrl-0.
|
|
|
Pin configuration/s for the third state. See pinctrl-0.
|
|
|
Pin configuration/s for the fourth state. See pinctrl-0.
|
|
|
Pin configuration/s for the fifth state. See pinctrl-0.
|
|
|
Names for the provided states. The number of names needs to match the
number of states.
This property is required. |
|
|
The FMC bank mapping configuration (BMAP bits of FMC_BCR1).
* disable - Default mapping.
* sdram-sram - Swap the NOR/PSRAM bank with SDRAM.
* sdramb2 - Remaps the SDRAM bank2.
If absent, then default mapping (disable) is used (reset state).
Default value: Legal values: |
Deprecated properties not inherited from the base binding file.
(None)
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “st,stm32h7-fmc” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
|
|
indicates the operational status of a device
Legal values: See Important properties for more information. |
|
|
compatible strings
This property is required. See Important properties for more information. |
|
|
register space
This property is required. See Important properties for more information. |
|
|
name of each register space
|
|
|
interrupts for device
See Important properties for more information. |
|
|
extended interrupt specifier for device
|
|
|
name of each interrupt
|
|
|
phandle to interrupt controller node
|
|
|
Human readable string describing the device (used as device_get_binding() argument)
See Important properties for more information. This property is deprecated. |
|
|
Clock gate information
This property is required. |
|
|
name of each clock
|
|
|
number of address cells in reg property
|
|
|
number of size cells in reg property
|
|
|
DMA channels specifiers
|
|
|
Provided names of DMA channel specifiers
|
|
|
IO channels specifiers
|
|
|
Provided names of IO channel specifiers
|
|
|
mailbox / IPM channels specifiers
|
|
|
Provided names of mailbox / IPM channel specifiers
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|