generic-fem-two-ctrl-pins

Vendor: Generic or vendor-independent

Description

This is a representation of generic radio Front-End Module (FEM)
that has a two-pin control interface (CTX, CRX).

The CTX control pin is used to enable the Power Amplifier (PA) in
the transmit path. This is therefore sometimes referred to as
the "PA pin" in other contexts.

The CRX control pin is used to enable the Low Noise Amplifier
(LNA) in the receive path, and is sometimes referred to as
the "LNA pin" in other contexts.

Each of these pins is optional, and may be omitted if not present.
(Though if you do specify a pin, you must also specify its
corresponding settle-time-us property.)

Properties

Node specific properties

Properties not inherited from the base binding file.

Name	Type	Details
ctx-gpios	phandle-array	SoC GPIO connected to the CTX input pin on the FEM device.
crx-gpios	phandle-array	SoC GPIO connected to the CRX input pin on the FEM device.
ctx-settle-time-us	int	Desired minimum settling time, in microseconds, from assertion of the CTX pin to beginning of transmission.
crx-settle-time-us	int	Desired minimum settling time, in microseconds, from assertion of the CRX pin to beginning of reception.
tx-gain-db	int	TX gain of the PA of the FEM device, in dB.
rx-gain-db	int	RX gain of the LNA of the FEM device, in dB.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “generic-fem-two-ctrl-pins” compatible.

Name	Type	Details
status	string	indicates the operational status of a device Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss' See Important properties for more information.
compatible	string-array	compatible strings This property is required. See Important properties for more information.
reg	array	register space See Important properties for more information.
reg-names	string-array	name of each register space
interrupts	array	interrupts for device See Important properties for more information.
interrupts-extended	compound	extended interrupt specifier for device
interrupt-names	string-array	name of each interrupt
interrupt-parent	phandle	phandle to interrupt controller node
label	string	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
clocks	phandle-array	Clock gate information
clock-names	string-array	name of each clock
#address-cells	int	number of address cells in reg property
#size-cells	int	number of size cells in reg property
dmas	phandle-array	DMA channels specifiers
dma-names	string-array	Provided names of DMA channel specifiers
io-channels	phandle-array	IO channels specifiers
io-channel-names	string-array	Provided names of IO channel specifiers
mboxes	phandle-array	mailbox / IPM channels specifiers
mbox-names	string-array	Provided names of mailbox / IPM channel specifiers
power-domains	phandle-array	Power domain specifiers
power-domain-names	string-array	Provided names of power domain specifiers
#power-domain-cells	int	Number of cells in power-domains property
zephyr,deferred-init	boolean	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
wakeup-source	boolean	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
zephyr,pm-device-runtime-auto	boolean	Automatically configure the device for runtime power management after the init function runs.
zephyr,disabling-power-states	phandles	List of power states that will disable this device power.