nxp,imx-iomuxc
Vendor: NXP Semiconductors N.V.
Description
This compatible binding should be applied to the device's iomuxc DTS node.
the DTS node will be populated with all pinmux options for the specific SOC.
These options can then be used in a pinctrl node with the "nxp,mcux-rt-pinctrl"
compatible string to define pin groups.
The user should not edit the bindings defined within this node to make pinmux
selections, but should instead edit the pinctrl groups for their board.
Properties
Top level properties
These property descriptions apply to “nxp,imx-iomuxc” nodes themselves. This page also describes child node properties in the following sections.
Node specific properties
Properties not inherited from the base binding file.
(None)
Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
Base properties
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,imx-iomuxc” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
Information used to address the device. The value is specific to
the device (i.e. is different depending on the compatible
property).
The "reg" property is typically a sequence of (address, length) pairs.
Each pair is called a "register block". Values are
conventionally written in hex.
For details, see "2.3.6 reg" in Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
Indicates the operational status of the hardware or other
resource that the node represents. In particular:
- "okay" means the resource is operational and, for example,
can be used by device drivers
- "disabled" means the resource is not operational and the system
should treat it as if it is not present
For details, see "2.3.4 status" in Devicetree Specification v0.4.
Legal values: See Important properties for more information. |
|
|
This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.
The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.
The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.
For details, see "2.3.1 compatible" in Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
Optional names given to each register block in the "reg" property.
For example:
/ {
soc {
#address-cells = <1>;
#size-cells = <1>;
uart@1000 {
reg = <0x1000 0x2000>, <0x3000 0x4000>;
reg-names = "foo", "bar";
};
};
};
The uart@1000 node has two register blocks:
- one with base address 0x1000, size 0x2000, and name "foo"
- another with base address 0x3000, size 0x4000, and name "bar"
|
|
|
Information about interrupts generated by the device, encoded as an array
of one or more interrupt specifiers. The format of the data in this property
varies by where the device appears in the interrupt tree. Devices with the same
"interrupt-parent" will use the same format in their interrupts properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
See Important properties for more information. |
|
|
Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
If present, this refers to the node which handles interrupts generated
by this device.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.
For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.
See Important properties for more information. |
|
|
Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:
https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml
|
|
|
Optional names given to each clock provider in the "clocks" property.
|
|
|
This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
|
|
|
This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
|
|
|
DMA channel specifiers relevant to the device.
|
|
|
Optional names given to the DMA channel specifiers in the "dmas" property.
|
|
|
IO channel specifiers relevant to the device.
|
|
|
Optional names given to the IO channel specifiers in the "io-channels" property.
|
|
|
Mailbox / IPM channel specifiers relevant to the device.
|
|
|
Optional names given to the mbox specifiers in the "mboxes" property.
|
|
|
Power domain specifiers relevant to the device.
|
|
|
Optional names given to the power domain specifiers in the "power-domains" property.
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
Child node properties
Name |
Type |
Details |
|---|---|---|
|
|
An array of values defining the pin mux selection, in the following format:
<mux_register, mux_val, input_reg, daisy_val, cfg_reg>
mux_register: register that will be written to make mux selection
mux_val: value to write to mux_register
input_reg: peripheral register that will direct peripheral signal to pin
daisy_val: value to write to input_reg
cfg_reg: register that will configure pin pull, drive strength, and open drain
This property is required. |
|
|
An array of values defining the GPR bit write required, if one exists.
Some IOMUXC options require writing to an IOMUXC_GPR register to select
them. This array has the following elements:
<gpr_reg, gpr_shift, gpr_val>
gpr_reg: GPR register address to write to
gpr_shift: shift to apply to value before writing
gpr_val: value to write
|
|
|
RT11xx parts have multiple types of IOMUXC registers defined, with
different register layouts. This property can be set to indicate
to the pinctrl driver the type of register this pinmux represents,
and should not be modified by the user.
|
|
|
RT11xx parts have multiple types of IOMUXC registers defined, with
different register layouts. This property can be set to indicate
to the pinctrl driver the type of register this pinmux represents,
and should not be modified by the user.
|
|
|
RT11xx parts have multiple types of IOMUXC registers defined, with
different register layouts. This property can be set to indicate
to the pinctrl driver the type of register this pinmux represents,
and should not be modified by the user.
|
|
|
RT11xx parts have multiple types of IOMUXC registers defined, with
different register layouts. This property can be set to indicate
to the pinctrl driver the type of register this pinmux represents,
and should not be modified by the user.
|