renesas,smartbond-pinctrl

Vendor: Renesas Electronics Corporation

Description

The SmartBond pin controller is a singleton node responsible for controlling
pin function selection and pin properties, such as routing a UART RX to pin
P1.8 and enabling the pullup resistor on that pin.

The node has the 'pinctrl' node label set in your SoC's devicetree,
so you can modify it like this:

  &pinctrl {
          /* your modifications go here */
  };

All device pin configurations should be placed in child nodes of the
'pinctrl' node, as shown in this example:

  /* You can put this in places like a board-pinctrl.dtsi file in
   * your board directory, or a devicetree overlay in your application.
   */

 /* include definitions and utility macros for the SoC used by the board */
 #include <dt-bindings/pinctrl/smartbond-pinctrl.h>

  &pinctrl {
    /* configuration for uart device, default state */
    uart_default: uart_default {
      /* group 1 */
      group1 {
        /* route UART TX to P0.9 */
        pinmux = <SMARTBOND_PINMUX(UART_TX, 0, 9)>;
      };
      /* group 2 */
      group2 {
        /* route UART RX to P0.8 and enable pull-up */
        pinmux = <SMARTBOND_PINMUX(UART_RX, 0, 8)>;
        bias-pull-up;
      };
    };
  };

The 'uart0_default' child node encodes the pin configurations for a
particular state of a device; in this case, the default (that is, active)
state.

As shown, pin configurations are organized in groups within each child node.
Each group can specify a list of pin function selections in the 'pinmux'
property. Note that 'pinmux' property is an array so you can configure multiple
pins at once there. The SMARTBOND_PINMUX macro is used to create pinmux value.

A group can also specify shared pin properties common to all the specified
pins, such as the 'bias-pull-up' property in group 2. Here is a list of
supported standard pin properties:

- bias-pull-up: Enable pull-up resistor.
- bias-pull-down: Enable pull-down resistor.

Note that bias options are mutually exclusive.

To link this pin configuration with a device, use a pinctrl-N property
for some number N, like this example you could place in your board's DTS
file:

   #include "board-pinctrl.dtsi"

   &uart {
         pinctrl-0 = <&uart_default>;
         pinctrl-names = "default";
   };

Properties

Top level properties

These property descriptions apply to “renesas,smartbond-pinctrl” nodes themselves. This page also describes child node properties in the following sections.

Node specific properties

Properties not inherited from the base binding file.

(None)

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “renesas,smartbond-pinctrl” compatible.

Name	Type	Details
status	string	indicates the operational status of a device Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss' See Important properties for more information.
compatible	string-array	compatible strings This property is required. See Important properties for more information.
reg	array	register space See Important properties for more information.
reg-names	string-array	name of each register space
interrupts	array	interrupts for device See Important properties for more information.
interrupts-extended	compound	extended interrupt specifier for device
interrupt-names	string-array	name of each interrupt
interrupt-parent	phandle	phandle to interrupt controller node
label	string	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
clocks	phandle-array	Clock gate information
clock-names	string-array	name of each clock
#address-cells	int	number of address cells in reg property
#size-cells	int	number of size cells in reg property
dmas	phandle-array	DMA channels specifiers
dma-names	string-array	Provided names of DMA channel specifiers
io-channels	phandle-array	IO channels specifiers
io-channel-names	string-array	Provided names of IO channel specifiers
mboxes	phandle-array	mailbox / IPM channels specifiers
mbox-names	string-array	Provided names of mailbox / IPM channel specifiers
power-domains	phandle-array	Power domain specifiers
power-domain-names	string-array	Provided names of power domain specifiers
#power-domain-cells	int	Number of cells in power-domains property
zephyr,deferred-init	boolean	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
wakeup-source	boolean	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
zephyr,pm-device-runtime-auto	boolean	Automatically configure the device for runtime power management after the init function runs.
zephyr,disabling-power-states	phandles	List of power states that will disable this device power.

Grandchild node properties

Name	Type	Details
pinmux	array	An array of pins sharing the same group properties. The pins should be defined using the SMARTBOND_PINMUX utility macro that encodes the port, pin and function. This property is required.
bias-pull-up	boolean	enable pull-up resistor
bias-pull-down	boolean	enable pull-down resistor
input-enable	boolean	enable input on pin (e.g. enable an input buffer, no effect on output)
output-enable	boolean	enable output on a pin without actively driving it (e.g. enable an output buffer)