nxp,s32k3-pmc

Note

An implementation of a driver matching this compatible is available in soc/nxp/s32/s32k3/pmc.c.

Description

NXP S32K3xx Power Management Controller (PMC)

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

lm-reg

boolean

Enables the Last Mile regulator, which regulates an external 1.5V
voltage on V15 down to the core and logic supply (V11 power domain),
which is typically 1.1V.
When enabling PLL as system clock, the PMC Last Mile regulator should
be enabled.

lm-reg-auto

boolean

Enables to turn over automatically from Boot Regulator Mode to Last Mile
regulator mode and vice versa, depending on the V15 voltage status.
When configuring system clocks higher than FIRC clock frequency,
lm-reg should be also enabled.

lm-reg-base-control

boolean

Enable this if an external BJT between VDD_HV_A and V15 is used on the
PCB. The base of this BJT must be connected to the VRC_CTRL pin and is
controlled by the PMC to regulate a voltage of 1.5V on V15 pin.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,s32k3-pmc” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.