adi,adp5360-regulator

Description

Analog Devices ADP3560 PMIC

The PMIC has one buck converter and one buck-boost converter. Both need to be
defined as children nodes, strictly following the BUCK and BUCKBOOST node
names. For example:

pmic@46 {
  compatible = "adi,adp5360";
  reg = <0x46>;
  ...
  regulators {
    compatible = "adi,adp5360-regulator";

    BUCK {
      /* all properties for BUCK */
    };
    BUCKBOOST {
      /* all properties for BUCKBOOST */
    };
  };
};

Properties

Top level properties

These property descriptions apply to “adi,adp5360-regulator” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

(None)

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “adi,adp5360-regulator” compatible.

Name	Type	Details
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`power-domain`	`phandle`	Power domain the device belongs to. The device will be notified when the power domain it belongs to is either suspended or resumed.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().

Child node properties

Name	Type	Details
`regulator-init-microvolt`	`int`	Voltage set during initialisation
`regulator-min-microvolt`	`int`	smallest voltage consumers may set
`regulator-max-microvolt`	`int`	largest voltage consumers may set
`regulator-always-on`	`boolean`	boolean, regulator should never be disabled
`regulator-boot-on`	`boolean`	bootloader/firmware enabled regulator. It's expected that this regulator was left on by the bootloader. If the bootloader didn't leave it on then OS should turn it on at boot but shouldn't prevent it from being turned off later. This property is intended to only be used for regulators where software cannot read the state of the regulator.
`regulator-boot-off`	`boolean`	Regulator should be disabled on boot.
`regulator-initial-mode`	`int`	Initial operating mode. The set of possible operating modes depends on the capabilities of every hardware so each device binding documentation explains which values the regulator supports.
`regulator-allowed-modes`	`array`	List of operating modes that software is allowed to configure for the regulator at run-time. Elements may be specified in any order. The set of possible operating modes depends on the capabilities of every hardware so each device binding document explains which values the regulator supports.
`adi,switch-delay-us`	`int`	Switch delay time in hysteresis. Legal values: `0`, `5`, `10`, `20`
`adi,soft-start-ms`	`int`	Soft start time in milliseconds Legal values: `1`, `8`, `64`, `512`
`adi,ilim-milliamp`	`int`	Peak current limit, in milliamperes. Values above 400mA are only applicable to buck boost. Legal values: `100`, `200`, `300`, `400`, `500`, `600`, `700`, `800`
`adi,enable-stop-pulse`	`boolean`	With this option selected and the buck/boost enabled, the buck/boost regulator can be stopped using the STP pin.
`adi,enable-output-discharge`	`boolean`	Enable output discharge functionality