st,lis3dh (on i2c bus)

Vendor: STMicroelectronics N.V.

Description

STMicroelectronics LIS3DH 3-axis accelerometer

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

supply-gpios

phandle-array

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

irq-gpios

phandle-array

The INT1 and (optional) INT2 signal connections.  These signals
are active-high as produced by the sensor.

int1-gpio-config

int

Select the interrupt configuration for INT1 gpio.

The default of 0 is the most common situation to avoid multiple interrupts
to be triggered by same event.

- 0 # LIS2DH_DT_GPIO_INT_EDGE_BOTH
- 1 # LIS2DH_DT_GPIO_INT_EDGE_RISING
- 2 # LIS2DH_DT_GPIO_INT_EDGE_FALLING
- 3 # LIS2DH_DT_GPIO_INT_LEVEL_HIGH
- 4 # LIS2DH_DT_GPIO_INT_LEVEL_LOW

Legal values: 0, 1, 2, 3, 4

int2-gpio-config

int

Select the interrupt configuration for INT2 gpio.

The default of 0 is the most common situation to avoid multiple interrupts
to be triggered by same event.

- 0 # LIS2DH_DT_GPIO_INT_EDGE_BOTH
- 1 # LIS2DH_DT_GPIO_INT_EDGE_RISING
- 2 # LIS2DH_DT_GPIO_INT_EDGE_FALLING
- 3 # LIS2DH_DT_GPIO_INT_LEVEL_HIGH
- 4 # LIS2DH_DT_GPIO_INT_LEVEL_LOW

Legal values: 0, 1, 2, 3, 4

disconnect-sdo-sa0-pull-up

boolean

Indicates the device driver should disconnect SDO/SA0 pull-up
during device initialization (e.g. to save current
leakage). Note that only subset of devices supported by this
binding have SDO/SA0 pull-up (e.g. LIS2DH12, LIS3DH).

anym-on-int1

boolean

Indicates that the device driver should use interrupt 1
for any movement. This is for boards that only have one
interrupt line connected from the sensor to the processor.

anym-no-latch

boolean

Disable the latching of interrupts for any movement.

anym-mode

int

Select the interrupt mode for any movement.

The default of 0 is the power-on-reset value.

- 0 # LIS2DH_DT_ANYM_OR_COMBINATION
- 1 # LIS2DH_DT_ANYM_6D_MOVEMENT
- 2 # LIS2DH_DT_ANYM_AND_COMBINATION
- 3 # LIS2DH_DT_ANYM_6D_POSITION

Legal values: 0, 1, 2, 3

friendly-name

string

Human readable string describing the sensor. It can be used to
distinguish multiple instances of the same model (e.g., lid accelerometer
vs. base accelerometer in a laptop) to a host operating system.

This property is defined in the Generic Sensor Property Usages of the HID
Usage Tables specification
(https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “st,lis3dh” compatible.

Name

Type

Details

reg

array

device address on i2c bus

This property is required.

See Important properties for more information.

status

string

indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

name of each register space

interrupts

array

interrupts for device

See Important properties for more information.

interrupts-extended

compound

extended interrupt specifier for device

interrupt-names

string-array

name of each interrupt

interrupt-parent

phandle

phandle to interrupt controller node

label

string

Human readable string describing the device (used as device_get_binding() argument)

See Important properties for more information.

This property is deprecated.

clocks

phandle-array

Clock gate information

clock-names

string-array

name of each clock

#address-cells

int

number of address cells in reg property

#size-cells

int

number of size cells in reg property

dmas

phandle-array

DMA channels specifiers

dma-names

string-array

Provided names of DMA channel specifiers

io-channels

phandle-array

IO channels specifiers

io-channel-names

string-array

Provided names of IO channel specifiers

mboxes

phandle-array

mailbox / IPM channels specifiers

mbox-names

string-array

Provided names of mailbox / IPM channel specifiers

power-domains

phandle-array

Power domain specifiers

power-domain-names

string-array

Provided names of power domain specifiers

#power-domain-cells

int

Number of cells in power-domains property

zephyr,deferred-init

boolean

Do not initialize device automatically on boot. Device should be manually
initialized using device_init().

wakeup-source

boolean

Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

zephyr,pm-device-runtime-auto

boolean

Automatically configure the device for runtime power management after the
init function runs.

zephyr,disabling-power-states

phandles

List of power states that will disable this device power.