zephyr,video-emul-imager (on i2c bus)
Vendor: Zephyr-specific binding
Note
An implementation of a driver matching this compatible is available in drivers/video/video_emul_imager.c.
Description
Emulated Imager for testing purpose
Properties
Top level properties
These property descriptions apply to “zephyr,video-emul-imager” nodes themselves. This page also describes child node properties in the following sections.
Node specific properties
Properties not inherited from the base binding file.
Name |
Type |
Details |
|---|---|---|
|
|
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
|
|
|
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
|
Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
Base properties
Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “zephyr,video-emul-imager” compatible.
Name |
Type |
Details |
|---|---|---|
|
|
device address on i2c bus
This property is required. See Important properties for more information. |
|
|
Indicates the operational status of the hardware or other
resource that the node represents. In particular:
- "okay" means the resource is operational and, for example,
can be used by device drivers
- "disabled" means the resource is not operational and the system
should treat it as if it is not present
For details, see "2.3.4 status" in Devicetree Specification v0.4.
Legal values: See Important properties for more information. |
|
|
This property is a list of strings that essentially define what
type of hardware or other resource this devicetree node
represents. Each device driver checks for specific compatible
property values to find the devicetree nodes that represent
resources that the driver should manage.
The recommended format is "vendor,device", The "vendor" part is
an abbreviated name of the vendor. The "device" is usually from
the datasheet.
The compatible property can have multiple values, ordered from
most- to least-specific. Having additional values is useful when the
device is a specific instance of a more general family, to allow the
system to match the most specific driver available.
For details, see "2.3.1 compatible" in Devicetree Specification v0.4.
This property is required. See Important properties for more information. |
|
|
Optional names given to each register block in the "reg" property.
For example:
/ {
soc {
#address-cells = <1>;
#size-cells = <1>;
uart@1000 {
reg = <0x1000 0x2000>, <0x3000 0x4000>;
reg-names = "foo", "bar";
};
};
};
The uart@1000 node has two register blocks:
- one with base address 0x1000, size 0x2000, and name "foo"
- another with base address 0x3000, size 0x4000, and name "bar"
|
|
|
Information about interrupts generated by the device, encoded as an array
of one or more interrupt specifiers. The format of the data in this property
varies by where the device appears in the interrupt tree. Devices with the same
"interrupt-parent" will use the same format in their interrupts properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
See Important properties for more information. |
|
|
Extended interrupt specifier for device, used as an alternative to
the "interrupts" property.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Optional names given to each interrupt generated by a device.
The interrupts themselves are defined in either "interrupts" or
"interrupts-extended" properties.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
If present, this refers to the node which handles interrupts generated
by this device.
For details, see "2.4 Interrupts and Interrupt Mapping" in
Devicetree Specification v0.4.
|
|
|
Human readable string describing the device. Use of this property is
deprecated except as needed on a case-by-case basis.
For details, see "4.1.2 Miscellaneous Properties" in Devicetree
Specification v0.4.
See Important properties for more information. |
|
|
Information about the device's clock providers. In general, this property
should follow conventions established in the dt-schema binding:
https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/clock/clock.yaml
|
|
|
Optional names given to each clock provider in the "clocks" property.
|
|
|
This property encodes the number of <u32> cells used by address fields
in "reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
|
|
|
This property encodes the number of <u32> cells used by size fields in
"reg" properties in this node's children.
For details, see "2.3.5 #address-cells and #size-cells" in Devicetree
Specification v0.4.
|
|
|
DMA channel specifiers relevant to the device.
|
|
|
Optional names given to the DMA channel specifiers in the "dmas" property.
|
|
|
IO channel specifiers relevant to the device.
|
|
|
Optional names given to the IO channel specifiers in the "io-channels" property.
|
|
|
Mailbox / IPM channel specifiers relevant to the device.
|
|
|
Optional names given to the mbox specifiers in the "mboxes" property.
|
|
|
Power domain specifiers relevant to the device.
|
|
|
Optional names given to the power domain specifiers in the "power-domains" property.
|
|
|
Number of cells in power-domains property
|
|
|
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().
|
|
|
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
|
|
|
Automatically configure the device for runtime power management after the
init function runs.
|
|
|
List of power states that will disable this device power.
|
Grandchild node properties
Name |
Type |
Details |
|---|---|---|
|
|
Label of the 'remote-endpoint' subnode that interfaces with this endpoint.
This property is used as a 'work-around' to be able to declare the remote
endpoint and should be replaced by a "remote-endpoint" phandle property when
Zephyr devicetree supports circular dependency in the future.
This property is required. |
|
|
Data bus type.
Legal values: |
|
|
On parallel data busses, if bus-width is used to specify the number of
data lines, data-shift can be used to specify which data lines are used,
e.g. "bus-width=<8>; data-shift=<2>;" means, that lines 9:2 are used.
|
|
|
Active state of the HSYNC signal
Legal values: |
|
|
Active state of the VSYNC signal.
Legal values: |
|
|
Sample data on falling, rising or both edges of the pixel clock signal.
Legal values: |
|
|
Allowed data bus frequencies. For MIPI CSI-2, for instance, this is the
actual frequency of the bus, not bits per clock per lane value.
|
|
|
Physical clock lane index. Position of an entry determines the logical
lane number, while the value of an entry indicates physical lane, e.g. for
a MIPI CSI-2 bus we could have "clock-lane = <0>;", which places the
clock lane on hardware lane 0. This property is valid for serial busses
only (e.g. MIPI CSI-2).
|
|
|
An array of physical data lane indexes. Position of an entry determines
the logical lane number, while the value of an entry indicates physical
lane, e.g. for 2-lane MIPI CSI-2 bus we could have "data-lanes = <1 2>;",
assuming the clock lane is on hardware lane 0. If the hardware does not
support lane reordering, monotonically incremented values shall be used
from 0 or 1 onwards, depending on whether or not there is also a clock
lane. This property is valid for serial busses only (e.g. MIPI CSI-2).
|
|
|
Number of data lines actively used, only valid for parallel busses.
|