adi,max32-w1

Vendor: Analog Devices, Inc.

Note

An implementation of a driver matching this compatible is available in drivers/w1/w1_max32.c.

Description

These nodes are “w1” bus nodes.

ADI MAX32xxx MCUs 1-Wire Master

Properties

Node specific properties

Properties not inherited from the base binding file.

Name

Type

Details

pinctrl-0

phandles

 
Pin configuration/s for the first state. Content is specific to the
selected pin controller driver implementation.

This property is required.

pinctrl-names

string-array

 
Names for the provided states. The number of names needs to match the
number of states.

This property is required.

internal-pullup

int

 
Set this field to enable the internal pullup resistor.
0 - Internal pullup disabled.
1 - Internal pullup enabled.

This property is required.

Legal values: 0, 1

external-pullup

int

 
Set this field to enable the external pullup.
0 - Pullup pin is active high when enabled.
1 - Pullup pin is active low when enabled.
2 - Pullup pin is not used for an external pullup.

Legal values: 0, 1, 2

long-line-mode

boolean

 
Long Line Mode Enable
Selects alternate timings for 1-Wire communication.
The recommended setting depends on the length of the wire.
For lines less than 40 meters, 0 should be used.

Setting this bit to 0 leaves the write one release,
the data sampling, and the time-slot recovery times at
approximately 5us (micro second), 15us, and 7us, respectively.

Setting this bit to 1 enables long line mode timings during standard mode communications.
This mode moves the write one release, the data sampling,
and the time-slot recovery times out to approximately 8us, 22us, and 14us, respectively.

0 - Standard operation for lines less than 40 meters.
1 - Long Line mode enabled.

active-pullup

boolean

 
Enable the active pullup for the 1-Wire bus.

pinctrl-1

phandles

 
Pin configuration/s for the second state. See pinctrl-0.

pinctrl-2

phandles

 
Pin configuration/s for the third state. See pinctrl-0.

pinctrl-3

phandles

 
Pin configuration/s for the fourth state. See pinctrl-0.

pinctrl-4

phandles

 
Pin configuration/s for the fifth state. See pinctrl-0.

Deprecated node specific properties

Deprecated properties not inherited from the base binding file.

(None)

Base properties

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “adi,max32-w1” compatible.

Name

Type

Details

reg

array

 
register space

This property is required.

See Important properties for more information.

clocks

phandle-array

 
Clock gate information

This property is required.

interrupts

array

 
interrupts for device

This property is required.

See Important properties for more information.

status

string

 
indicates the operational status of a device

Legal values: 'ok', 'okay', 'disabled', 'reserved', 'fail', 'fail-sss'

See Important properties for more information.

compatible

string-array

 
compatible strings

This property is required.

See Important properties for more information.

reg-names

string-array

 
name of each register space

interrupts-extended

compound

 
extended interrupt specifier for device

interrupt-names

string-array

 
name of each interrupt

interrupt-parent

phandle

 
phandle to interrupt controller node

label

string

 
Human readable string describing the device (used as device_get_binding() argument)

See Important properties for more information.

This property is deprecated.

clock-names

string-array

 
name of each clock

#address-cells

int

 
number of address cells in reg property

#size-cells

int

 
number of size cells in reg property

dmas

phandle-array

 
DMA channels specifiers

dma-names

string-array

 
Provided names of DMA channel specifiers

io-channels

phandle-array

 
IO channels specifiers

io-channel-names

string-array

 
Provided names of IO channel specifiers

mboxes

phandle-array

 
mailbox / IPM channels specifiers

mbox-names

string-array

 
Provided names of mailbox / IPM channel specifiers

power-domains

phandle-array

 
Power domain specifiers

power-domain-names

string-array

 
Provided names of power domain specifiers

#power-domain-cells

int

 
Number of cells in power-domains property

zephyr,deferred-init

boolean

 
Do not initialize device automatically on boot. Device should be manually
initialized using device_init().

wakeup-source

boolean

 
Property to identify that a device can be used as wake up source.

When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.

Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.

zephyr,pm-device-runtime-auto

boolean

 
Automatically configure the device for runtime power management after the
init function runs.

zephyr,disabling-power-states

phandles

 
List of power states that will disable this device power.