CONFIG_CLOCK_STM32_PLL_M_DIVISOR

Division factor for PLL VCO input clock

PLL divisor

PLL divisor

PLL divisor

PLL divisor

Type: int

Help

PLLM division factor needs to be set correctly to ensure that the VCO input frequency ranges from 1 to 2 MHz. It is recommended to select a frequency of 2 MHz to limit PLL jitter. Allowed values: 2-63

Help

PLL divisor, allowed values: 0-63.

Help

PLL divisor, L4: allowed values: 1-8. PLL VCO input ranges from 4 to 16MHz L5: allowed values: 1-16. PLL VCO input ranges from 4 to 16MHz WB: allowed values: 1-8. PLL VCO input ranges from 2.66 to 16MHz

Help

PLL divisor, allowed values: 1-8.

Help

PLL divisor, allowed values: 1-16.

Defaults

  • 8

  • 32

  • 1

  • 1

  • 4

Kconfig definitions

At drivers/clock_control/Kconfig.stm32f2_f4_f7:8

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:132

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_M_DIVISOR
    int "Division factor for PLL VCO input clock"
    range 2 63
    default 8
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && (SOC_SERIES_STM32F2X || SOC_SERIES_STM32F4X || SOC_SERIES_STM32F7X) && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLLM division factor needs to be set correctly to ensure that the VCO
      input frequency ranges from 1 to 2 MHz. It is recommended to select a
      frequency of 2 MHz to limit PLL jitter.
      Allowed values: 2-63

At drivers/clock_control/Kconfig.stm32h7:67

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:133

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_M_DIVISOR
    int "PLL divisor"
    range 0 63
    default 32
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && SOC_SERIES_STM32H7X && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL divisor, allowed values: 0-63.

At drivers/clock_control/Kconfig.stm32l4_l5_wb:8

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:135

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_M_DIVISOR
    int "PLL divisor"
    range 1 8 if SOC_SERIES_STM32L4X || SOC_SERIES_STM32WBX
    range 1 16 if SOC_SERIES_STM32L5X
    default 1
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && (SOC_SERIES_STM32L4X || SOC_SERIES_STM32L5X || SOC_SERIES_STM32WBX) && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL divisor,
      L4: allowed values: 1-8. PLL VCO input ranges from 4 to 16MHz
      L5: allowed values: 1-16. PLL VCO input ranges from 4 to 16MHz
      WB: allowed values: 1-8. PLL VCO input ranges from 2.66 to 16MHz

At drivers/clock_control/Kconfig.stm32g0:17

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:136

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_M_DIVISOR
    int "PLL divisor"
    range 1 8
    default 1
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && SOC_SERIES_STM32G0X && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL divisor, allowed values: 1-8.

At drivers/clock_control/Kconfig.stm32g4:8

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:137

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_M_DIVISOR
    int "PLL divisor"
    range 1 16
    default 4
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && SOC_SERIES_STM32G4X && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL divisor, allowed values: 1-16.

(The ‘depends on’ condition includes propagated dependencies from ifs and menus.)