CONFIG_CLOCK_STM32_PLL_Q_DIVISOR

Division factor for OTG FS, SDIO and RNG clocks

PLL Q Divisor

PLL Q Divisor

PLL Q Divisor

PLL Q Divisor

Type: int

Help

The USB OTG FS requires a 48MHz clock to work correctly. SDIO and RNG need a frequency lower than or equal to 48 MHz to work correctly. Allowed values: 2-15

Help

PLL Q Output divisor, allowed values: 1-128.

Help

PLL Q Output divisor L4: allowed values: 0, 2, 4, 6, 8. PLLQ do not exceed 80MHz L5: allowed values: 0, 2, 4, 6, 8. PLLQ do not exceed 80MHz WB: allowed values: 0, 2-8. PLLQ do not exceed 64MHz

Help

PLL Q VCO divisor, allowed values: 2-8. Limited to STM32G0X1 variants.

Help

PLL Q Output divisor, allowed values: 2, 4, 6, 8.

Defaults

  • 7

  • 2

  • 2

  • 2

  • 2

Kconfig definitions

At drivers/clock_control/Kconfig.stm32f2_f4_f7:40

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:132

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_Q_DIVISOR
    int "Division factor for OTG FS, SDIO and RNG clocks"
    range 2 15
    default 7
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && (SOC_SERIES_STM32F2X || SOC_SERIES_STM32F4X || SOC_SERIES_STM32F7X) && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      The USB OTG FS requires a 48MHz clock to work correctly. SDIO and RNG
      need a frequency lower than or equal to 48 MHz to work correctly.
      Allowed values: 2-15

At drivers/clock_control/Kconfig.stm32h7:91

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:133

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_Q_DIVISOR
    int "PLL Q Divisor"
    range 1 128
    default 2
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && SOC_SERIES_STM32H7X && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL Q Output divisor, allowed values: 1-128.

At drivers/clock_control/Kconfig.stm32l4_l5_wb:44

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:135

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_Q_DIVISOR
    int "PLL Q Divisor"
    range 0 8
    default 2
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && (SOC_SERIES_STM32L4X || SOC_SERIES_STM32L5X || SOC_SERIES_STM32WBX) && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL Q Output divisor
      L4: allowed values: 0, 2, 4, 6, 8. PLLQ do not exceed 80MHz
      L5: allowed values: 0, 2, 4, 6, 8. PLLQ do not exceed 80MHz
      WB: allowed values: 0, 2-8. PLLQ do not exceed 64MHz

At drivers/clock_control/Kconfig.stm32g0:33

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:136

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_Q_DIVISOR
    int "PLL Q Divisor"
    range 2 8
    default 2
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && (SOC_STM32G031XX || SOC_STM32G071XX) && SOC_SERIES_STM32G0X && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL Q VCO divisor, allowed values: 2-8.
      Limited to STM32G0X1 variants.

At drivers/clock_control/Kconfig.stm32g4:32

Included via Kconfig:8 → Kconfig.zephyr:32 → drivers/Kconfig:54 → drivers/clock_control/Kconfig:25 → drivers/clock_control/Kconfig.stm32:137

Menu path: (Top) → Device Drivers → Hardware clock controller support → STM32 Reset & Clock Control

config CLOCK_STM32_PLL_Q_DIVISOR
    int "PLL Q Divisor"
    range 2 8
    default 2
    depends on CLOCK_STM32_SYSCLK_SRC_PLL && SOC_SERIES_STM32G4X && CLOCK_CONTROL_STM32_CUBE && CLOCK_CONTROL
    help
      PLL Q Output divisor, allowed values: 2, 4, 6, 8.

(The ‘depends on’ condition includes propagated dependencies from ifs and menus.)