HCI drivers

HCI drivers. More...

Data Structures
struct	bt_hci_setup_params
struct	bt_hci_driver
	Abstraction which represents the HCI transport to the controller. More...

Enumerations
enum	{ BT_QUIRK_NO_RESET = BIT(0) , BT_QUIRK_NO_AUTO_DLE = BIT(1) }
enum	bt_hci_driver_bus {   BT_HCI_DRIVER_BUS_VIRTUAL = 0 , BT_HCI_DRIVER_BUS_USB = 1 , BT_HCI_DRIVER_BUS_PCCARD = 2 , BT_HCI_DRIVER_BUS_UART = 3 ,   BT_HCI_DRIVER_BUS_RS232 = 4 , BT_HCI_DRIVER_BUS_PCI = 5 , BT_HCI_DRIVER_BUS_SDIO = 6 , BT_HCI_DRIVER_BUS_SPI = 7 ,   BT_HCI_DRIVER_BUS_I2C = 8 , BT_HCI_DRIVER_BUS_IPM = 9 }
	Possible values for the 'bus' member of the bt_hci_driver struct. More...

Functions
int	bt_recv (struct net_buf *buf)
	Receive data from the controller/HCI driver.
int	bt_hci_driver_register (const struct bt_hci_driver *drv)
	Register a new HCI driver to the Bluetooth stack.
int	bt_hci_transport_setup (const struct device *dev)
	Setup the HCI transport, which usually means to reset the Bluetooth IC.
int	bt_hci_transport_teardown (const struct device *dev)
	Teardown the HCI transport.
struct net_buf *	bt_hci_evt_create (uint8_t evt, uint8_t len)
	Allocate an HCI event buffer.
struct net_buf *	bt_hci_cmd_complete_create (uint16_t op, uint8_t plen)
	Allocate an HCI Command Complete event buffer.
struct net_buf *	bt_hci_cmd_status_create (uint16_t op, uint8_t status)
	Allocate an HCI Command Status event buffer.

Detailed Description

HCI drivers.

Deprecated:

This is the old HCI driver API. Drivers should use Bluetooth HCI APIs instead.

Enumeration Type Documentation

anonymous enum

anonymous enum

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Enumerator
BT_QUIRK_NO_RESET
BT_QUIRK_NO_AUTO_DLE

bt_hci_driver_bus

enum bt_hci_driver_bus

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Possible values for the 'bus' member of the bt_hci_driver struct.

Enumerator
BT_HCI_DRIVER_BUS_VIRTUAL
BT_HCI_DRIVER_BUS_USB
BT_HCI_DRIVER_BUS_PCCARD
BT_HCI_DRIVER_BUS_UART
BT_HCI_DRIVER_BUS_RS232
BT_HCI_DRIVER_BUS_PCI
BT_HCI_DRIVER_BUS_SDIO
BT_HCI_DRIVER_BUS_SPI
BT_HCI_DRIVER_BUS_I2C
BT_HCI_DRIVER_BUS_IPM

Function Documentation

bt_hci_cmd_complete_create()

struct net_buf * bt_hci_cmd_complete_create	(	uint16_t	op,
		uint8_t	plen
	)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Allocate an HCI Command Complete event buffer.

This function allocates a new buffer for HCI Command Complete event. It is given the OpCode (encoded e.g. using the BT_OP macro) and the total length of the parameters. Upon successful return the buffer is ready to have the parameters encoded into it.

Parameters

op	Command OpCode.
plen	Length of command parameters.

Returns

Newly allocated buffer.

bt_hci_cmd_status_create()

struct net_buf * bt_hci_cmd_status_create	(	uint16_t	op,
		uint8_t	status
	)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Allocate an HCI Command Status event buffer.

This function allocates a new buffer for HCI Command Status event. It is given the OpCode (encoded e.g. using the BT_OP macro) and the status code. Upon successful return the buffer is ready to have the parameters encoded into it.

Parameters

op	Command OpCode.
status	Status code.

Returns

Newly allocated buffer.

bt_hci_driver_register()

int bt_hci_driver_register

(

const struct bt_hci_driver *

drv

)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Register a new HCI driver to the Bluetooth stack.

This needs to be called before any application code runs. The bt_enable() API will fail if there is no driver registered.

Parameters

drv	A bt_hci_driver struct representing the driver.

Returns

0 on success or negative error number on failure.

Deprecated:

Use the new HCI driver interface instead: Bluetooth HCI APIs

bt_hci_evt_create()

struct net_buf * bt_hci_evt_create	(	uint8_t	evt,
		uint8_t	len
	)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Allocate an HCI event buffer.

This function allocates a new buffer for an HCI event. It is given the event code and the total length of the parameters. Upon successful return the buffer is ready to have the parameters encoded into it.

Parameters

evt	Event OpCode.
len	Length of event parameters.

Returns

Newly allocated buffer.

bt_hci_transport_setup()

int bt_hci_transport_setup

(

const struct device *

dev

)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Setup the HCI transport, which usually means to reset the Bluetooth IC.

Note

A weak version of this function is included in the H4 driver, so defining it is optional per board.

Parameters

dev	The device structure for the bus connecting to the IC

Returns

0 on success, negative error value on failure

bt_hci_transport_teardown()

int bt_hci_transport_teardown

(

const struct device *

dev

)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Teardown the HCI transport.

Note

A weak version of this function is included in the IPC driver, so defining it is optional. NRF5340 includes support to put network core in reset state.

Parameters

dev	The device structure for the bus connecting to the IC

Returns

0 on success, negative error value on failure

bt_recv()

int bt_recv

(

struct net_buf *

buf

)

#include <include/zephyr/drivers/bluetooth/hci_driver.h>

Receive data from the controller/HCI driver.

This is the main function through which the HCI driver provides the host with data from the controller. The buffer needs to have its type set with the help of bt_buf_set_type() before calling this API.

Parameters

buf	Network buffer containing data from the controller.

Returns

0 on success or negative error number on failure.

Deprecated:

Use the new HCI driver interface instead: Bluetooth HCI APIs