linker-tool-gcc.h File Reference

GCC toolchain linker defs. More...

#include <zephyr/kernel/mm.h>

Go to the source code of this file.

Macros
#define	GROUP_START(where)
#define	GROUP_END(where)
#define	GROUP_LINK_IN(where)   > where
	Route memory to a specified memory area.
#define	GROUP_ROM_LINK_IN(vregion, lregion)   > lregion
	Route memory for a read-only section.
#define	GROUP_DATA_LINK_IN(vregion, lregion)   > vregion
	Route memory for read-write sections that are loaded.
#define	GROUP_NOLOAD_LINK_IN(vregion, lregion)   > vregion
	Route memory for read-write sections that are NOT loaded; typically this is only used for 'BSS' and 'noinit'.
#define	SECTION_PROLOGUE(name, options, align)    name options : align
	The SECTION_PROLOGUE() macro is used to define the beginning of a section.
#define	SECTION_DATA_PROLOGUE(name, options, align)    SECTION_PROLOGUE(name, options, align)
	Same as for SECTION_PROLOGUE(), except that this one must be used for data sections which on XIP platforms will have differing virtual and load addresses (i.e.
#define	COMMON_SYMBOLS   *(COMMON)

Detailed Description

GCC toolchain linker defs.

This header file defines the necessary macros used by the linker script for use with the GCC linker.

Macro Definition Documentation

COMMON_SYMBOLS

#define COMMON_SYMBOLS   *(COMMON)

GROUP_DATA_LINK_IN

#define GROUP_DATA_LINK_IN	(		vregion,
			lregion
	)		> vregion

Route memory for read-write sections that are loaded.

Used for initialized data sections that on XIP platforms must be copied at startup.

Parameters

vregion	Output VMA
lregion	Output LMA (only used if CONFIG_MMU if VMA != LMA, or CONFIG_XIP)

GROUP_END

#define GROUP_END

(

where

)

GROUP_LINK_IN

#define GROUP_LINK_IN

(

where

)

> where

Route memory to a specified memory area.

The GROUP_LINK_IN() macro is located at the end of the section description and tells the linker that this section is located in the memory area specified by 'where' argument.

This macro is intentionally undefined for CONFIG_MMU systems when CONFIG_KERNEL_VM_BASE is not the same as CONFIG_SRAM_BASE_ADDRESS, as both the LMA and VMA destinations must be known for all sections as this corresponds to physical vs. virtual location.

Parameters

where

Destination memory area

GROUP_NOLOAD_LINK_IN

#define GROUP_NOLOAD_LINK_IN	(		vregion,
			lregion
	)		> vregion

Route memory for read-write sections that are NOT loaded; typically this is only used for 'BSS' and 'noinit'.

Parameters

vregion	Output VMA
lregion	Output LMA (only used if CONFIG_MMU if VMA != LMA, corresponds to physical location)

GROUP_ROM_LINK_IN

#define GROUP_ROM_LINK_IN	(		vregion,
			lregion
	)		> lregion

Route memory for a read-only section.

The GROUP_ROM_LINK_IN() macro is located at the end of the section description and tells the linker that this a read-only section that is physically placed at the 'lregion` argument.

If CONFIG_XIP is active, the 'lregion' area is flash memory.

If CONFIG_MMU is active, the vregion argument will be used to determine where this is located in the virtual memory map, otherwise it is ignored.

Parameters

vregion	Output VMA (only used if CONFIG_MMU where LMA != VMA)
lregion	Output LMA

GROUP_START

#define GROUP_START

(

where

)

SECTION_DATA_PROLOGUE

#define SECTION_DATA_PROLOGUE	(		name,
			options,
			align
	)		SECTION_PROLOGUE(name, options, align)

Same as for SECTION_PROLOGUE(), except that this one must be used for data sections which on XIP platforms will have differing virtual and load addresses (i.e.

they'll be copied into RAM at program startup). Such a section must also use GROUP_DATA_LINK_IN to specify the correct output load address.

This is equivalent to SECTION_PROLOGUE() on non-XIP systems. On XIP systems there is an implicit ALIGN_WITH_INPUT specified.

Parameters

name	Name of the output section
options	Section options, or left blank
align	Alignment directives, such as SUBALIGN(). ALIGN() itself is not allowed. May be blank.

SECTION_PROLOGUE

#define SECTION_PROLOGUE	(		name,
			options,
			align
	)		name options : align

The SECTION_PROLOGUE() macro is used to define the beginning of a section.

On MMU systems where VMA != LMA there is an implicit ALIGN_WITH_INPUT specified.

Parameters

name	Name of the output section
options	Section options, such as (NOLOAD), or left blank
align	Alignment directives, such as SUBALIGN(). ALIGN() itself is not allowed. May be blank.