Definitions for IEEE 802.3 management interface. More...

Macros
#define	MDIO_MMD_PMAPMD 0x01U
	Physical Medium Attachment / Physical Medium Dependent.

#define	MDIO_MMD_WIS 0x02U
	WAN Interface Sublayer.

#define	MDIO_MMD_PCS 0x03U
	Physical Coding Sublayer.

#define	MDIO_MMD_PHYXS 0x04U
	PHY Extender Sublayer.

#define	MDIO_MMD_DTEXS 0x05U
	DTE Extender Sublayer.

#define	MDIO_MMD_TC 0x06U
	Transmission Convergence.

#define	MDIO_MMD_AN 0x07U
	Auto-negotiation.

#define	MDIO_MMD_SEPARATED_PMA1 0x08U
	Separated PMA (1)

#define	MDIO_MMD_SEPARATED_PMA2 0x09U
	Separated PMA (2)

#define	MDIO_MMD_SEPARATED_PMA3 0x0AU
	Separated PMA (3)

#define	MDIO_MMD_SEPARATED_PMA4 0x0BU
	Separated PMA (4)

#define	MDIO_MMD_C22EXT 0x1DU
	Clause 22 extension.

#define	MDIO_MMD_VENDOR_SPECIFIC1 0x1EU
	Vendor Specific 1.

#define	MDIO_MMD_VENDOR_SPECIFIC2 0x1FU
	Vendor Specific 2.

#define	MDIO_CTRL1 0x0000U
	Control 1.

#define	MDIO_STAT1 0x0001U
	Status 1.

#define	MDIO_DEVID1 0x0002U
	Device identifier (1)

#define	MDIO_DEVID2 0x0003U
	Device identifier (2)

#define	MDIO_SPEED 0x0004U
	Speed ability.

#define	MDIO_DEVS1 0x0005U
	Devices in package (1)

#define	MDIO_DEVS2 0x0006U
	Devices in package (2)

#define	MDIO_CTRL2 0x0007U
	Control 2.

#define	MDIO_STAT2 0x0008U
	Status 2.

#define	MDIO_PKGID1 0x000EU
	Package identifier (1)

#define	MDIO_PKGID2 0x000FU
	Package identifier (2)

#define	MDIO_AN_T1_CTRL 0x0200U
	BASE-T1 Auto-negotiation control.

#define	MDIO_AN_T1_STAT 0x0201U
	BASE-T1 Auto-negotiation status.

#define	MDIO_AN_T1_ADV_L 0x0202U
	BASE-T1 Auto-negotiation advertisement register [15:0].

#define	MDIO_AN_T1_ADV_M 0x0203U
	BASE-T1 Auto-negotiation advertisement register [31:16].

#define	MDIO_AN_T1_ADV_H 0x0204U
	BASE-T1 Auto-negotiation advertisement register [47:32].

#define	MDIO_PMA_PMD_BT1_CTRL 0x0834U
	BASE-T1 PMA/PMD control register.

#define	MDIO_AN_T1_CTRL_RESTART BIT(9)
	Auto-negotiation Restart.

#define	MDIO_AN_T1_CTRL_EN BIT(12)
	Auto-negotiation Enable.

#define	MDIO_AN_T1_STAT_LINK_STATUS BIT(2)
	Link Status.

#define	MDIO_AN_T1_STAT_ABLE BIT(3)
	Auto-negotiation Ability.

#define	MDIO_AN_T1_STAT_REMOTE_FAULT BIT(4)
	Auto-negotiation Remote Fault.

#define	MDIO_AN_T1_STAT_COMPLETE BIT(5)
	Auto-negotiation Complete.

#define	MDIO_AN_T1_STAT_PAGE_RX BIT(6)
	Page Received.

#define	MDIO_AN_T1_ADV_L_PAUSE_CAP BIT(10)
	Pause Ability.

#define	MDIO_AN_T1_ADV_L_PAUSE_ASYM BIT(11)
	Pause Ability.

#define	MDIO_AN_T1_ADV_L_FORCE_MS BIT(12)
	Force Master/Slave Configuration.

#define	MDIO_AN_T1_ADV_L_REMOTE_FAULT BIT(13)
	Remote Fault.

#define	MDIO_AN_T1_ADV_L_ACK BIT(14)
	Acknowledge (ACK)

#define	MDIO_AN_T1_ADV_L_NEXT_PAGE_REQ BIT(15)
	Next Page Request.

#define	MDIO_AN_T1_ADV_M_B10L BIT(14)
	10BASE-T1L Ability

#define	MDIO_AN_T1_ADV_M_MST BIT(4)
	Master/slave Configuration.

#define	MDIO_AN_T1_ADV_H_10L_TX_HI_REQ BIT(12)
	10BASE-T1L High Level Transmit Operating Mode Request

#define	MDIO_AN_T1_ADV_H_10L_TX_HI BIT(13)
	10BASE-T1L High Level Transmit Operating Mode Ability

#define	MDIO_PMA_PMD_BT1_CTRL_CFG_MST BIT(14)
	BASE-T1 master/slave configuration.

#define	MDIO_PMA_B10L_CTRL 0x08F6U
	10BASE-T1L PMA control

#define	MDIO_PMA_B10L_STAT 0x08F7U
	10BASE-T1L PMA status

#define	MDIO_PMA_B10L_LINK_STAT 0x8302U
	10BASE-T1L PMA link status

#define	MDIO_PCS_B10L_CTRL 0x08E6U
	10BASE-T1L PCS control

#define	MDIO_PCS_B10L_STAT 0x08E7U
	10BASE-T1L PCS status

#define	MDIO_PMA_B10L_CTRL_TX_DIS_MODE_EN BIT(14)
	10BASE-T1L Transmit Disable Mode

#define	MDIO_PMA_B10L_CTRL_TX_LVL_HI BIT(12)
	10BASE-T1L Transmit Voltage Amplitude Control

#define	MDIO_PMA_B10L_CTRL_EEE BIT(10)
	10BASE-T1L EEE Enable

#define	MDIO_PMA_B10L_CTRL_LB_PMA_LOC_EN BIT(0)
	10BASE-T1L PMA Loopback

#define	MDIO_PMA_B10L_STAT_LINK BIT(0)
	10BASE-T1L PMA receive link up

#define	MDIO_PMA_B10L_STAT_FAULT BIT(1)
	10BASE-T1L Fault condition detected

#define	MDIO_PMA_B10L_STAT_POLARITY BIT(2)
	10BASE-T1L Receive polarity is reversed

#define	MDIO_PMA_B10L_STAT_RECV_FAULT BIT(9)
	10BASE-T1L Able to detect fault on receive path

#define	MDIO_PMA_B10L_STAT_EEE BIT(10)
	10BASE-T1L PHY has EEE ability

#define	MDIO_PMA_B10L_STAT_LOW_POWER BIT(11)
	10BASE-T1L PMA has low-power ability

#define	MDIO_PMA_B10L_STAT_2V4_ABLE BIT(12)
	10BASE-T1L PHY has 2.4 Vpp operating mode ability

#define	MDIO_PMA_B10L_STAT_LB_ABLE BIT(13)
	10BASE-T1L PHY has loopback ability

#define	MDIO_PMA_B10L_LINK_STAT_REM_RCVR_STAT_OK_LL BIT(9)
	10BASE-T1L Remote Receiver Status OK Latch Low

#define	MDIO_PMA_B10L_LINK_STAT_REM_RCVR_STAT_OK BIT(8)
	10BASE-T1L Remote Receiver Status OK

#define	MDIO_PMA_B10L_LINK_STAT_LOC_RCVR_STAT_OK_LL BIT(7)
	10BASE-T1L Local Receiver Status OK

#define	MDIO_PMA_B10L_LINK_STAT_LOC_RCVR_STAT_OK BIT(6)
	10BASE-T1L Local Receiver Status OK

#define	MDIO_PMA_B10L_LINK_STAT_DSCR_STAT_OK_LL BIT(5)
	10BASE-T1L Descrambler Status OK Latch Low

#define	MDIO_PMA_B10L_LINK_STAT_DSCR_STAT_OK BIT(4)
	10BASE-T1L Descrambler Status OK

#define	MDIO_PMA_B10L_LINK_STAT_LINK_STAT_OK_LL BIT(1)
	10BASE-T1L Link Status OK Latch Low

#define	MDIO_PMA_B10L_LINK_STAT_LINK_STAT_OK BIT(0)
	10BASE-T1L Link Status OK

#define	MDIO_PCS_B10L_CTRL_LB_PCS_EN BIT(14)
	10BASE-T1L PCS Loopback Enable

#define	MDIO_PCS_B10L_STAT_DSCR_STAT_OK_LL BIT(2)
	10BASE-T1L PCS Descrambler Status

Enumerations
enum	mdio_opcode { MDIO_OP_C22_WRITE = 1 , MDIO_OP_C22_READ = 2 , MDIO_OP_C45_ADDRESS = 0 , MDIO_OP_C45_WRITE = 1 , MDIO_OP_C45_READ_INC = 2 , MDIO_OP_C45_READ = 3 }
	MDIO transaction operation code. More...

Detailed Description

Definitions for IEEE 802.3 management interface.

Macros

Enumerations

Detailed Description